SunStar KM-1640BL-7 Скачать руководство пользователя страница 6

Страница: 6 / 36

Machine safety regulations

Safety instructions on this manual are defined as Danger, Warning and Notice.

If you do not follow the instructoins, physical injuries and machine damages might be occurred.

: This indication should be observed definitely. If not, there will be a danger during the installation,

conveyance and maintenance of the machine.

: When you follow this indication, injuries from the machine can be prevented.

: When you follow this indication, error on the machine can be prevented.

Caution

Warning

Danger

1-1) Transporting

machine

Danger

1-2) Installing

machine

Warning

1-3) Repairing

machine

Caution

Those in charge of transporting the machine should have a full understanding of the

machine. The following indications should be followed when the machine is being

transported.

ⓐ

More than 2 people must transport the machine.

ⓑ

To prevent accidents from occurring during transportation, wipe off the oil on the

machine compeletely.

The machine may not work properly or breakdown, if installed in certain places, Install

the machine where the following qualifications agree.

ⓐ

Remove the package and wrappings from the top. Take special notice on the nails

on the wooden boxes.

ⓑ

Dust and moisture stains and rusts the machine. Install an airconditioner and clean

the machine regularly.

ⓒ

Keep the machine out of the sun.

ⓓ

Leave sufficient space of more than 50cm behind, and on the right and left side of

the machine for repairing.

ⓔ

EXPLOSION HAZARDS

Do not operate in explosive atmospheres. To avoid explosion, do not operate this

machine in an explosive atomsphere including a place where large quantities of

aerosol spray product are being used or where oxygen is being administered unless

it has been specifically certified for such operation.

[Refer] Details for machine installation are described in 4. Installation.

When the machine needs to be repaired, only the assigned troubleshooting engineer

educated at the company should take charge.

ⓐ

Before cleaning or repairing the machine, turn off the main power and wait 4

minutes till the machine is completely out of power.

ⓑ

Not any of the machine specifications or parts should be changed without consulting

the company. Such changes may make the operation dangerous.

ⓒ

Spare parts produced by the company should only be used for

replacements.

ⓓ

Put all the safety covers back on the machine after the machine has been repaired.

Содержание KM-1640BL-7





































Результаты поиска

Содержание KM-1640BL-7

Отзывы:

Похожие инструкции для KM-1640BL-7

Бренды по названию

Популярные бренды

SunStar KM-1640BL-7, Руководство пользователя

Результаты поиска

Содержание KM-1640BL-7

Отзывы:

Похожие инструкции для KM-1640BL-7

Бренды по названию

Популярные бренды