SunStar KM-1640BL-7 Скачать руководство пользователя страница 25

Страница: 25 / 36

Maintenance and Adjustment of Sewing

8.1) Adjusting needle bar

As in Figure 8-1, place the needle bar in the lowest

position by pulling out the needle bar adjusting hole

rubber cover

①

and rotating the pulley, and then

loosen the needle bar holder clamp screw

②

and

move the needle bar such that the needle bar

’

lowest position mark carved sign

④

is aligned with

the lower side of the needle bar lower bushing

③

After fixing tightly the needle bar holder clamp

screw

②

and place the rubber cover

①

8.2) Adjusting timing of needle and hook

As in Figure8-2, align the lower side of the needle

bushing

①

with the fixed hook position carved line

②

marked in the needle bar. Then, loosen three hook

fixing bolts

③

. When the hook edge

④

is aligned

with the center of needle, turn the loosened hook so

that the clearance between the needle groove inside

carved in the lateral side of the needle and the hook

edge

④

becomes 0.05~0.1mm. Later, tight again the

three fixing bolts

③

[Fig. 8-1]

[Fig. 8-2]

•

For machine maintenance and repair, consult with qualified technicians.

•

For electrical maintenance and repair, consult with qualified technicians or agencies.

•

When safety devices are disassembled, make sure to return them to original positions.

•

Use both hands when bending the machine backwards or returning it to the original position. Using
only one hand can lead to severe hand injuries due to the weight of the machine.

•

Turn off the switch and pull the plug. Pressing pedal by mistake may result in physical injuries.

Inspection, maintenance, repair

Exchanging expendable parts such as needle, hook, knife.

Adjusting hook oil flow

•

In case you operate the machine when the power is on, please take special precaution.

Caution

DB×1#22
DP×17#22

③

④

①

②

DB×1#22
DP×17#22

0.05~0.1mm

Содержание KM-1640BL-7





































Результаты поиска

Содержание KM-1640BL-7

Отзывы:

Похожие инструкции для KM-1640BL-7

Бренды по названию

Популярные бренды

SunStar KM-1640BL-7, Руководство пользователя

Результаты поиска

Содержание KM-1640BL-7

Отзывы:

Похожие инструкции для KM-1640BL-7

Бренды по названию

Популярные бренды