SunStar KM-1640BL-7 Скачать руководство пользователя страница 34

Страница: 34 / 36

8.13) Adjusting blade pressure

A. As in Figure 8-22, the standard is when the contact

between the movable knife and the fixed blade begins.

B. In particular, when the cutting quality gets worse by

using a thick thread, strengthen a little bit the tension of
the fixed blade.

8.14) Exchanging movable knife

Place a needle at the top by turning the pulley when
replacing the movable blade

①

and take off the needle

plate by loosening two fixed screws

②

indicated in the

figure 8-24. When assembling the exchange, assemble it
in reverse order of disassembling.

8.15) Exchanging fixed blade

A. When exchanging the fixed blade

①

, pick the washer

③

and the inner bobbin stopper

④

out by loosening the

screw

②

indicated in the figure 8-25 then disassemble by

loosening the fixed blade screw

⑤

. When assembling the

exchange, assemble it in reverse order of disassembling.

C. How to adjust the tension of the fixed blade; loosen the

nut

①

(for adjusting tension of fixed blade) using a

wrench box as shown in the figure 8-23 and adjust it
with the screw

②

(for adjusting tension).

After adjusting, tighten the nut

①

(for adjusting tension)

using a wrench box.

[Fig. 8-22]

[Fig. 8-23]

[Fig. 8-24]

[Fig. 8-25]

movable knife

3mm

wrench box

movable knife

fixed blade

Содержание KM-1640BL-7





































Результаты поиска

Содержание KM-1640BL-7

Отзывы:

Похожие инструкции для KM-1640BL-7

Бренды по названию

Популярные бренды

SunStar KM-1640BL-7, Руководство пользователя

Результаты поиска

Содержание KM-1640BL-7

Отзывы:

Похожие инструкции для KM-1640BL-7

Бренды по названию

Популярные бренды