SunStar KM-1640BL-7 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 36

background image

28

8.8) Adjusting feed dog height and inclination

A. Adjust the height of the feed dog

③

by loosening the clamp screw

②

of the leverage crank(front) and moving the

leverage crank(front)

①

.

B. To adjust the inclination of the feed dog, loosen the fixing screw of feed dog inclination adjustment crank

⑥

in the

horizontal pushing crank

④

first. Later, adjust it by rotating until 90 degree the feed dog inclination adjustment shaft

⑤

.

When you turn the shaft

⑤

clockwise, the front of feed dog goes up while the rear part of the feed dog is up with counter

clockwise direction.(Refer to figure 8-8)

C. Check the height of feed dog

③

because the height of it changes after the adjustment of feed dog

③

.

[Fig. 8-8]

8.9) Adjusting auxiliary presser foot and upper feed presser foot

Normally, the auxiliary presser foot and the upper feed presser foot work vertically with a same height difference.
In accordance with the material type, there are some cases in which run the auxiliary presser foot

①

and the upper feed

presser foot

②

at the same pace, or sometimes, at different paces. In these cases, please adjust the height as follows:

■

In case of running vertically the auxiliary presser foot and the upper feed presser foot at the same height

a) The vertical running range of the auxiliary presser foot

①

and the upper feed presser foot

②

is from 2 to 5.5 mm.

b) The vertical running amounts of the auxiliary presser foot

①

and the upper feed presser foot

②

are easily

adjustable from the climb device dial attached to the front side of the machine.

c) The dial

④

attached to the upper cover is a dial which controls the running amount dial

③

. Only when the numbers

of

③

and

④

are identical, the auxiliary presser foot and the upper feed presser foot can be run at the same height.

ex) When the running amount of the two presser feet are adjusted to 4mm

ex)

First, adjust the number of the dial attached to the upper cover to 4, and make the number the dial at front
side of the machine 4. When you adjust the number from lower one to a higher, you should adjust the dial

④

first. In the reverse case, the adjustment of the dial

③

should be done first.

[Fig. 8-9]

Highest position
of feed dog

①

②

④

⑤

③

⑤

⑥

⑥

①

①

②

②

5.5mm

5.5mm

③

④

clockwise

front

back

front

back

front

back

counter clockwise

«
...
26
27
28
29
30
...
»

Содержание KM-1640BL-7





































Отзывы:

Нет отзывов

Похожие инструкции для KM-1640BL-7

FloorMAX Hard Floor Machine

Бренд: Hoover Страницы: 8

Бренд: Matrix Fitness Страницы: 26

Бренд: Jack Страницы: 70

Бренд: Tennant Страницы: 41

AquaRide 56314009

Бренд: Nilfisk-Advance Страницы: 32

Бренд: Philips Страницы: 2

Бренд: JUKI Страницы: 62

HZL - 353Z Series

Бренд: JUKI Страницы: 35

Бренд: SunStar Страницы: 40

Бренд: JUKI Страницы: 187

Бренд: Tunstall Страницы: 20

WRANGLER 1503 AB

Бренд: NSS Страницы: 176

Бренд: Nilfisk-Advance Страницы: 29

FAX Attendant System Release 2.1.1

Бренд: Lucent Technologies Страницы: 324

Бренд: Atlanta Attachment Company Страницы: 80

Бренд: Atlanta Страницы: 116

NEW GOLIA PLUS EH

Бренд: Kunzle & Tasin Страницы: 20

Бренд: Ice Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды