background image

 

2. FOREWORD 

ZZ Series blowers are the result of advanced engineering and skilled 
manufacturing. To be assured of receiving maximum service from this 
machine, the owner must exercise care in its operation and maintenance. This 
manual is written to give the operator and maintenance department essential 
information for day-to-day operation, maintenance and adjustment. Careful 
adherence to these instructions will result in economical operation and 
minimum downtime. 

 

Danger is used to indicate the presence of a hazard which will cause 
severe personal injury, death, or substantial damage if the warming is 
ignored.

 

 

Warning is used to indicate the presence of a hazard which can cause 
severe personal injury, death, or substantial damage if the warming is 
ignored.

 

 

Caution is used to indicate the presence of a hazard which will or can 
cause minor personal injury or property damage if the warning is 
ignored

.

 

 

Notice is used to notify people of installation, operation or maintenance 
information which is important but not hazard-related.

 

 

 

----------------------------------------------------------------------------------------------------------------------------------------------- 
Sunco Blowers     www.suncoblowers.com   Phone:  704-545-3922     Pg. 5 
 

All rights reserved. No part of this manual may be reproduced in any form by any 

means without permission from 

Sunco Blowers  

 

Содержание EurusBlower ZZ2L





















































Отзывы: