manualshive.com logo in svg
background image

8

INSTALLING THE CO

2

 AIR LINE TO REGULATOR

Attach the open end of the red hose to the hose barb 
connection on the regulator. 
Secure hose by using one of the provided clamps. 
Use pliers/screwdriver to tighten clamp and assure no 
leaks.


 INSTALLATION INSTRUCTIONS (continued)

INSTALLING THE BEER TOWER

Remove the top plug by twisting and pulling out, saving it for later use if you decide to convert unit 
to an “all-refrigerator”.
Unravel the beer line (clear hose) from the tower and insert the beer line and wing nut through the 
uncovered hole on top. 
Lock the beer tower assembly to the top and make sure to position the beer faucet so it is aligned with 
the cabinet front (6 o’clock position). To do so, align the bottom of the beer tower to the 3 grooves on 
the top cabinet and tighten by hand clockwise to properly lock.

INSTALLING THE PROTECTIVE METAL PLATE

This plate should always be installed when the keg is in place to protect against unnecessary damage 
to the 

fl

 oor of the cabinet. 

INSTALLING THE PROTECTIVE METAL PLATE

Position the beer keg directly in front of the open door. 
Using keg handles only, carefully lift the beer keg.
To place the beer keg inside the cabinet, brace your 
knees behind the beer keg. Lift the front of the keg just 
enough so the front edge of the keg is resting on the 
front edge of the Beer dispenser bottom cabinet. 
Grasp the keg handles and slide it all the way into the 
cabinet. 

Содержание SCK02SMWBS














Отзывы: