Summit 2175 L Скачать руководство пользователя страница 3

INSTALLATION, OPERATION AND MAINTENANCE MANUAL 

SUMMIT PUMP MODEL 2175  

iii 

1.1  WARRANTY 

Pumping units assembled by Summit Pump, Inc., Green Bay, WI are guaranteed to 

be free from defects in material and workmanship for one year from date of shipment 

from factory in Green Bay, WI.  The obligation under this Warranty, statutory or 

otherwise, is limited to replacement or repair at Green Bay, WI, of such part as shall 

appear to us upon inspection at such point, to have been defective in material or 

workmanship. 
This Warranty does not obligate Summit Pump, Inc. to bear the cost of labor or 

transportation charges in connection with replacement or repair of defective parts; 

nor shall it apply to a pump upon which repairs or alterations have been made unless 

authorized by Summit Pump, Inc. 
No warranty is made in respect to engines, motors, or trade accessories, such being 

subject to warranties of their respective manufacturers. 
No express implied or statutory warranty, other than herein set forth is made or 

authorized to be made by Summit Pump, Inc. 
In no event shall Summit Pump, Inc. be liable for consequential damages or 

contingent liabilities arising out of the failure of any Summit Pump, Inc. pump or parts 

thereof to operate properly. 

 

1.2  LIABILITY 

Summit Pump, Inc. shall not be liable for personal physical injury, damage or delays 

caused by failure to follow the instructions and procedures for installation, operation 

and maintenance contained in this manual. 

The equipment is not for use in or with any nuclear facility or fire sprinkler system.  

Buyer accepts the responsibility for insuring that the equipment is not used in 

violation and Buyer shall indemnify and hold Seller harmless from any and all 

liability (including such liability resulting from seller’s negligence) arising out of said 

improper use. 

 

1.3  COPYRIGHT 

This Installation, Operation, and Maintenance Manual contains proprietary 

information, which is protected by copyright. No part of this Installation, Operation, 

and Maintenance Manual may be photocopied or reproduced without prior written 

consent from Summit Pump. 
The information contained herein is for informational use only and is subject to 

change without notice. Summit Pump assumes no responsibility or liability for any 

errors or inaccuracies that may appear in this manual. 

Содержание 2175 L













































Отзывы: