Sumitomo F-20L Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 56

Sumitomo F-20L Скачать руководство пользователя страница 27

Installation

23

2.

Inspect the Tip-N-Tell Sensor on Compressor Unit for Activation.

2.1

Check the Tip-N-Tell sensor mounted on the compressor rear panel. If the Tip-N-
Tell sensor shows no mishandling and there is no apparent physical damage, skip
Steps

2.2

and

2.3

and proceed to the section Compressor Location.

If the Tip-N-Tell sensor indicates mishandling (arrow dot is red), proceed to either Step

2.2

or

2.3

:

2.2

The equalization pressure is within specifications:

If the compressor has been momentarily tipped (less than one hour) and the equalization
pressure is within specifications, allow it to stand upright for two hours before performing
this step

AVOID ELECTRIC SHOCK.

This equipment must only be connected to a supply mains

with protective earth. All electrical supply equipment must meet applicable codes and be
installed by qualified personnel.

AVOID ELECTRIC SHOCK.

Permit only qualified electrical technicians to open

electrical enclosures, to perform electrical checks or to perform tests with the power
supply connected and wiring exposed. Failure to observe this warning can result in
serious injury or death

Connect power and water to the compressor. See the next sections Compressor
Location, Electrical Supply Connection, Coolant Connections and Compressor
Checkout. Test run the compressor for two (2) hours minimum. If there are no problems
during this time, stop the compressor and proceed to assemble the system.

If the compressor shuts down during the two- (2) hour test, contact the nearest SCAI
Service Center.

2.3

If the equalization pressure is outside the specified range or there is physical
damage to the compressor enclosure or the compressor has been on its side or
upside down for an extended period of time (more than one hour), contact the
nearest SCAI Service Center and notify the delivering carrier of the damage.

NOTE

When checking the compressor for shipping damage, do not connect gas lines and
cold head. The components may become contaminated with compressor oil.

«
...
25
26
27
28
29
...
»

Содержание F-20L

























































Отзывы:

Нет отзывов