SUGATSUNE LAMP FD80-H Скачать руководство пользователя

Страница: 8 / 12

Mounting of Floor Guide Temporarily

Hanging Door

Slotted hole

Position floor guide just below the
center of upper track.

Front face of

door pocket

Trailing edge at

closed position

⑥

Hanger bolt

(Trailing edge)

Floor guide

Support of 10 mm thickness

②

Hanger bolt

(Leading edge)

Bracket

⑦

Floor guide

The position of the model

where the margin occurs is

shown in the figure.

Temporarily fasten through the
slotted holes with the provided
screws.

Ensure that hanger bolt head is straight as
shown for proper fastening of the holder.

Verify that the claw of the shaft support
holder catches the opposite side of the
holder.

⑨

Spanner wrench

Nominal designation 10 mm ,
max. 6 mm thickness

Hanger bolt

Bracket

Holder

Caution

❼

Verification of Soft Closer Operation

●

Starting point of soft - close

approx. 115 mm before the stop position.

(

included in

⑦)

Содержание LAMP FD80-H













Результаты поиска

Содержание LAMP FD80-H

Отзывы:

Похожие инструкции для LAMP FD80-H

Бренды по названию

Популярные бренды

SUGATSUNE LAMP FD80-H, Руководство по установке

Результаты поиска

Содержание LAMP FD80-H

Отзывы:

Похожие инструкции для LAMP FD80-H

Бренды по названию

Популярные бренды