18
CRC1100A
CAUTION
Probe :
To give a correct reading, the probe must be installed in a place
protected from thermal influences, which may affect the temperature to be
controlled.
Controller :
Controller should be installed in a place protected by vibration,
water and corrosive gasses and where ambient temperature does not
exceed the values specified in the technical data.
WIRING : The probe and its corresponding wires should never be installed in a conduit
next to control or power supply lines.The electrical wiring should be done as shown in
the diagram. The power supply circuit should be connected to a protection switch. The
terminals admit wires of upto 2.5sq mm.
WARNING : Improper wiring may cause irreparable damage and personal injury.
Kindly ensure that wiring is done by qualified personnel only.
Maintenance : Cleaning: Clean the surface of the controller with a soft moist cloth. Do
not use abrasive detergents, petrol, alcohol or solvents.
Notice :
The information in this document is subject to change in order to improve
reliability , design or function without prior notice and does not represent a
commitment on the part of the company. In no event will the company be liable for
direct, indirect, special, incidental or consequential damage arising out of the use or
inability to use the product or documentation, even if advised of the possibility of such
damages. No part of this may be reproduced or transmitted in any form or by any
means without the prior written permission of the company.
Warranty :
This product is warranted against defects in materials and workmanship
for a period of one year from the date of purchase. During the warranty period, product
determined by us to be defective in form or function will be repaired or , at our option,
replaced at no charge. This warranty does not apply if the product has been damaged
by accident, abuse, and misuse or as a result of service or modification other than by
the company This warranty is in lieu of any other warranty expressed or implied. In no
event shall the company be held liable for incidental or consequential damages, such
as lost revenue or lost business opportunity arising from the purchase of this product.
Disclaimer:
This manual & its contents remain the sole property of PVR CONTROLS,
India and shall not be reproduced or distributed without authorization. Although great
care has been taken in the preparation of this document, the company or its vendors in
no event will be liable for direct, indirect, special, incidental or consequential damage
arising out of the use or inability to use the product or documentation, even if advised
of the possibility of such damages. No part of this manual may be reproduced or
transmitted in any form or by any means without the prior written permission of the
company. PVR CONTROLS, reserves the right to make and changes or
improvements without prior notice.
1
2
3
4
5
6
7
8
9
11
10
12
13
14
15
16
17
18
19
20
21
P
H
A
S
E
IN
P
U
T
F
R
O
M
P
R
E
S
S
U
R
E
[H
P
/L
P
/O
S
S
]
T
R
IP
C
O
N
T
A
C
T
C
NO
NO
NO
C
NO
C
NO
EV
AP
.
F
AN
COND.
COMP .
DEFROST
(HEA
TER/
HOT GAS)
A
L
A
R
M
2
3
0
V
NEUTRAL
D
IG
IT
A
L
I
/P
C
O
IL
R
O
O
M
Suggested Wiring Diagram
NEUTRAL
PHASE
C [13]
NO [1
1]
C [15]
NO [14]
EVAPORA
TOR F
AN
CONDENSOR FAN
NO [12]
COMPRESSOR
[2]
2
PHASE INPUT FROM
PRESSURE [HP/LP/OSS]
TRIP
CONT
ACT
CONNECT
OR
C [17]
NO [16]
NO [18]
HEATER
ALARM
17
CRC1100A
