manualshive.com logo in svg

Stuart Turner Monsoon U1.5 bar Twin, Руководство по установке

Поделиться
Скачать
Stuart Turner Monsoon U1.5 bar Twin Скачать руководство пользователя страница 24

DECLARATION OF CONFORMITY

2006/42/EC

BS EN ISO 12100-1, BS EN ISO 12100-2, BS EN 809

2006/95/EC

BS EN 60335-1, BS EN 60335-2-41, EN 50366

2004/108/EC

BS EN 55014-1, BS EN 55014-2, BS EN 55022, BS EN 61000-3-2,  BS EN 61000-3-3, 

BS EN 61000-4-2,  BS EN 61000-4-3, BS EN 61000-4-4, BS EN 61000-4-5, BS EN 61000-4-6, 

BS EN 61000-4-11 

IT IS HEREBY CERTIFIED THAT THE STUART ELECTRIC MOTOR DRIVEN PUMP AS 
SERIAL NUMBER BELOW, COMPLIES WITH THE ESSENTIAL REQUIREMENTS OF THE 
ABOVE E.E.C. DIRECTIVES.

RESPONSIBLE PERSON
AND MANUFACTURER

STUART TURNER LIMITED
HENLEY-ON-THAMES, OXFORDSHIRE
RG9 2AD  ENGLAND.

Signed  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Customer Relationship Manager

Stuart Turner are an approved company to BS EN ISO 9001:2000

Stuart Turner Ltd, Henley-on-Thames, Oxfordshire RG9 2AD ENGLAND

Tel:   +44 (0) 1491 572655,      Fax:   +44 (0) 1491 573704

email:   [email protected]    web:  www.stuart-turner.co.uk

V.A.T. REG. No. 199 0987 92. Registered in England No. 88368. Registered Office: Market Place, Henley-on-Thames

Issue No. 1010/1-04

Pt. No. 19223

Содержание Monsoon U1.5 bar Twin

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды