Stuart Turner Monsoon U1.5 bar Twin Скачать руководство пользователя страница 22

Страница: 22 / 24

- 22 -

THE MONSOON GUARANTEE

Congratulations on purchasing a Stuart Turner pump.

We are confident this pump will provide many years of trouble free
service as all our products are manufactured to the very highest
standard.

All Monsoon Pumps are guaranteed to be free from defects in
materials or workmanship for 3 years from the date of purchase.

EXTEND YOUR PUMP GUARANTEE

Register your pump details on-line now (within 30 days of date of
purchase) and the standard 3 year guarantee will be extended

FREE

of charge for a further two years.

www.stuart-turner.co.uk

If you do not have on-line access or would like us to help you
register your pump then simply call our

‘Pump Assist’

helpline on

0844 98 000 97

Please note that to validate your extended warranty we will require
the following information:

Full pump serial number (including last 3 digits) which can be
found on the pump rating label and the back page of the
installation instructions.

Your name/address/telephone/e-mail.

The date of installation.

Your installer’s name/address/telephone/e-mail.

Содержание Monsoon U1.5 bar Twin

























Результаты поиска

Содержание Monsoon U1.5 bar Twin

Отзывы:

Бренды по названию

Популярные бренды

Stuart Turner Monsoon U1.5 bar Twin, Руководство по установке

Результаты поиска

Содержание Monsoon U1.5 bar Twin

Отзывы:

Бренды по названию

Популярные бренды