manualshive.com logo in svg

Stuart Turner Monsoon U1.5 bar Twin, Руководство по установке

Поделиться
Скачать
Stuart Turner Monsoon U1.5 bar Twin Скачать руководство пользователя страница 10

- 10 -

Typical Low Level Installation

In certain installations it may be necessary to install a 90° bend on the inlet or outlet

connections of the pump before the flexible hose to accommodate a low level installation.

Below are some preferred connection options.  All connections seal on the pump body

using a fibre or rubber sealing washer.  Tap connector fittings should be used which must
be of an appropriate pressure and temperature rating.

It is essential when using any of the fittings shown below, that a correct water tight seal

is obtained between the pump body and selected fitting and also the flexible hose and
selected fitting.  If in doubt contact the fitting manufacturer and confirm compatibility with
the connection to be sealed.

Carefully check connections and pipework for leaks whilst pump running and stationary

before leaving the installation unattended.

STEP 5 ELECTRICAL INSTALLATION

WARNINGS:

The electrical installation must be carried out in accordance with the 
current national electrical regulations and installed by a competent 
person.

In the interests of electrical safety a 30 mA residual current device 
(R.C.D.) should be installed in the supply circuit.  This may be part of 
a consumer unit or a separate unit.

Before starting work on the electrical supply ensure power supply is 
isolated. 

This appliance must be earthed.

The motor and wiring must not be exposed to water.

Do not allow the supply cord to contact hot surfaces, including the 
motor shell, pump body or pipework.  The cord should be safely 
routed and secured by cable clips. 

G¾ female x 22 mm
elbow tap connector.

22 mm compression to
G¾ male.

G¾ female flexible hose
(supplied in kit).

Fibre washer.

22 mm copper pipe.

22 mm
copper
pipe

G¾ female x 22 mm
swivel tap connector
with rubber sealing
washer.

G¾ female x 22 mm
tap connector with
rubber sealing washer.

22 mm stem elbow.

G¾ female flexible hose
(supplied in kit).

22 mm compression to
G¾ male.

G¾ female x 22 mm
tap connector.

Fibre washer.

G¾ female
flexible hose
(supplied in
kit).

22 mm to G¾
male.

Fig. 10

Sealing washer
(sometimes captured in
fitting)

22 mm
elbow.

Содержание Monsoon U1.5 bar Twin

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды