manualshive.com logo in svg

Stuart Turner Monsoon U1.5 bar Twin, Руководство по установке

Поделиться
Скачать
Stuart Turner Monsoon U1.5 bar Twin Скачать руководство пользователя страница 12

- 12 -

Wiring Diagram (Schematic)

The supply cord and internal wiring within the terminal box are routed 

and secured to ensure compliance with the electrical standard 
EN 60335-1. It is essential that any disturbance of this internal wiring is 
avoided and the factory routing and securing of all internal wiring is 
always maintained.

Fuses

The following fuse size should be used with the appropriate pump.

Supply Cord Replacement

The supply cord and internal wiring within the terminal box are routed

and secured to ensure compliance with the electrical standard EN 60335-1.
It is essential that prior to any disturbance of this internal wiring, all cable
routing and securing details are carefully noted to ensure re-assembly to

the same factory pattern is always maintained.

If the supply cord is to be changed or is damaged, it must be replaced with a special

cord assembly available from Stuart Turner or one of their approved repairers.

On disassembly note the cord retention and routing system.  Re-assemble to the same

pattern.

For information on cable connection consult the wiring diagram and cable gland fitting

instructions.

MAIN WINDING

THERMOTRIP

CAPACITOR

START WINDING

FLOWSWITCH

REED (S3)

LINK WIR

E (BLUE)

BROW

N

BLAC

K

GREEN / YELLOW

BLUE

BROWN

L

S2 S3 S3 S2

E

N 230 VAC/1PH/50Hz

SUPPLY

BLUE

N A M

N

L

S1

S1

FLOWSWITCH

REED (S2)

PRESSURE

SWITCH (S1)

Fig. 12

Model

Fuse Size (AMPS)

U4.0 bar Twin

13

U4.5 bar Twin

All other models

5

Содержание Monsoon U1.5 bar Twin

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды