Stuart Turner ABB V150-45-2V-1 Скачать руководство пользователя страница 2

- 2 -

PRODUCT DESCRIPTION

Twin electric motor driven centrifugal pump set complete with an automatic variable 
speed duty/assist control system, incorporating pumps, VSD, transducer, pressure vessel 
and electronic control.

APPLICATION

The Aquaboost Booster Set (vertical twin) range is designed for pressure boosting stored, 
clean cold water into systems, where under gravity, no flow is available.

Inlet pressures to the pump and ambient temperatures must not exceed the 
values given in the technical specifications.

 

z

This pump set must not be used for any other application without    

 

the written consent of Stuart Turner Ltd.

 

z

This pump MUST NOT be connected directly to the mains water    

 supply.

 

z

This appliance can be used by children aged from 8 years and  

 

 

above and persons with reduced physical, sensory or mental  

 

 

capabilities or lack of experience and knowledge if they have been  

 

given supervision or instruction concerning use of the appliance    

 

in a safe way and understand the hazards involved.  Children shall   

 

not play with the appliance.  Cleaning and user maintenance shall   

 

not be made by children without supervision.

 

z

Children should be supervised to ensure that they do not play with  

 

the appliance.

Please read installation details carefully as they are intended to ensure this 
product provides long, trouble free service.  Failure to install the unit in 
accordance with the installation instructions will lead to invalidation of the 
warranty.

STORAGE

If this product is not to be installed immediately on receipt, ensure that it is stored in a dry, 
frost and vibration free location in its original packaging.

CONTENTS 

Page

Checklist  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Important Facts - read before commencing installation    . . . . . . . . . . . . . . . . . . . . . . 5
Location   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Electrical  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Control Programming   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Commissioning  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Technical Specification 

  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Trouble Shooting    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Guarantee  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Содержание ABB V150-45-2V-1





























Отзывы: