Stryker 0711-001-000, Инструкция по эксплуатации

Страница: 72 / 78

6 6..8 8.. E Elle eccttrro om ma ag gn ne ettiicc C Co om mp pa attiib biilliittyy
product safety to verify accuracy of this information
G Gu uiid da an ncce e a an nd d m ma an nu uffa accttu urre err’’ss d de ecclla arra attiio on n -- e elle eccttrro om ma ag gn ne ettiicc e em miissssiio on nss
The Neptune S Rover is intended for use in the electromagnetic environment specified below. The customer or the user
of the Neptune S Rover should assure that it is used in such an environment.
E Em miissssiio on nss tte esstt C Co om mp plliia an ncce e E Elle eccttrro om ma ag gn ne ettiicc e en nvviirro on nm me en ntt -- g gu uiid da an ncce e
RF emissions
CISPR 11
Group 1 Neptune S Rover uses RF energy only for its internal function.
Therefore, its RF emissions are very low and are not likely to cause any
interference in nearby electronic equipment.
RF emissions
CISPR 11
Class A Neptune S Rover is suitable for use in all establishments, including
domestic establishments and those directly connected to the public low-
voltage power supply network that supplies buildings used for domestic
purposes, provided the following warning is heeded:
W WA AR RN NIIN NG G -- This equipment/system is intended for use by
healthcare professionals only. This equipment/system may cause radio
interference or may disrupt the operation of nearby equipment.
Mitigation measures may be necessary, such as reorienting or
relocating the Neptune S Rover or shielding the location.
Harmonic emissions
IEC 61000-3-2
Class A
Voltage fluctuations/
flicker emissions
IEC 61000-3-3
Complies
G Gu uiid da an ncce e a an nd d m ma an nu uffa accttu urre err’’ss d de ecclla arra attiio on n -- e elle eccttrro om ma ag gn ne ettiicc iim mm mu un niittyy
This Neptune S Rover is intended for use in the electromagnetic environment specified below. The customer or the user
of the Neptune S Rover should assure that it is used in such an environment.
IIm mm mu un niittyy tte esstt IIE EC C 6 60 06 60 01 1 tte esstt lle evve ell C Co om mp plliia an ncce e lle evve ell E Elle eccttrro om ma ag gn ne ettiicc
e en nvviirro on nm me en ntt -- g gu uiid da an ncce e
Electrostatic discharge
(ESD)
IEC 61000-4-2
± 8 kV contact
± 2 kV, ± 4 kV, ± 8 kV, ± 15
kV air
± 8 kV contact
± 2 kV, ± 4 kV, ± 8 kV, ± 15
kV air
Floors should be wood,
concrete, or ceramic tile. If
floors are covered with
synthetic material, the
relative humidity should be
at least 20% ?? .
Electrical fast transient/burst
IEC 61000-4-4
± 2 kV at 100 kHz repetition
frequency for power supply
lines
±1 kV at 100 kHz repetition
frequency for input/output
lines
± 2 kV at 100 kHz repetition
frequency for power supply
lines
±1 kV at 100 kHz repetition
frequency for input/output
lines
Mains power quality should
be that of a typical
commercial or hospital
environment.
Surge
IEC 61000-4-5
± 0.5 kV, ± 1 kV line(s) to
line(s)
± 0.5 kV, ± 1 kV, ± 2 kV line
(s) to earth
± 0.5 kV, ± 1 kV line(s) to
line(s)
± 0.5 kV, ± 1 kV, ± 2 kV line
(s) to earth
Mains power quality should
be that of a typical
commercial or hospital
environment.
EN 70 700000969828 Rev-AA
DRAFT
NOT
FOR
SALE