manualshive.com logo in svg

Struers LaboForce-100, Инструкция по эксплуатации

Поделиться
Скачать
Struers LaboForce-100 Скачать руководство пользователя страница 27

#

Error Message

Explanation

Action

48

Error

Frequency inverter error!

The disc motor is
overloaded.

Fault code: 0.0

Thermal level: 0%

Wait for the disc motor to
cool.

Reduce the force and
continue the preparation
process.

49

Error

The disc motor is
overheated!

Please wait some minutes
and reduce the load.

Fault code: 0.0

Wait for the disc motor to
cool.

Reduce the force and
continue the preparation
process.

50

Error

Frequency inverter fault!

Fault code: 0.0

An error in the frequency
inverter is detected.

Re-start the machine.

If the error remains, contact
Struers Service.

Please make a note of the
Fault code.

53

Error

Specimen mover motor
power supply out of range
or missing!

Re-start the machine.

If the error remains, contact
Struers Service.

55

Error

No communication to
frequency inverter!

Re-start the machine.

If the error remains, contact
Struers Service.

58

Warning

A bad electrical connection
for the following output is
detected:

Re-start the machine.

Make a note of the output.

If the error remains, contact
Struers Service.

59

Warning

Specimen holder motor
overload, please reduce the
force.

Reduce the force or/and
increase the specimen
rpms.

Re-start the process.

If the error remains, contact
Struers Service.

8   Troubleshooting

LaboForce-100

27

Содержание LaboForce-100



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды