manualshive.com logo in svg

Struers LaboForce-100, Инструкция по эксплуатации

Поделиться
Скачать
Struers LaboForce-100 Скачать руководство пользователя страница 11

5.5

Compressed-air connections

Procedure

Note

The main air valve is not a part of the unit and must be installed and set before the
specimen mover is installed.

1.

Fit the quick coupling on the compressed air hose and secure it with the hose clamp.

2.

Connect the air inlet hose to the quick coupling.

3.

Fit the other end of the air inlet hose into the compressed air inlet on the specimen mover.

Note

The air pressure must be between 6 bar (87 psi) and 9.9 bar (143 psi).

Hint

The specimen mover requires a continuous flow of compressed air through the
regulator valve – a faint hissing sound does not mean that there is an air leak.

5.6

The specimen mover

The specimen mover can be used with specimen mover plates for single specimens or specimen
holders for multiple specimens.

5.6.1

Inserting a specimen holder

Inserting a specimen holder

CAUTION

To prevent specimens from detaching from the specimen holder, make sure that
the specimen or specimens are clamped securely in the specimen holder.

CAUTION

Protective footwear is recommended when you handle heavy specimen holders.

CRUSHING HAZARD

Keep your hands clear of the specimen holder or specimen mover plate when
lowering the specimen mover.

Note

When you work with specimen holders, make sure that the screws clamping the
specimens do not stick out of the specimen holder.
Use different lengths of screws for specimens with different diameters.

5   Installation

LaboForce-100

11

Содержание LaboForce-100



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды