Structural Concepts CDR4694 Скачать руководство пользователя страница 3

Страница: 3 / 22

OVERVIEW



These Structural Concepts merchandisers are
designed to merchandise packaged products at
ambient temperatures.



Cases should be installed and operated according to
this operating manual’s instructions to ensure proper
performance. Improper use will void warranty.

TYPE

This unit is designed for the display of products in ambient
store conditions where temperatures and humidity are
maintained within a specific range.



Type 1 Conditions (this case): ambient conditions are
to be at 55% maximum humidity and maximum
temperatures of 75 °F [24 °C].

COMPLIANCE

- Performance issues when in violation of

applicable NEC, federal, state and local electrical codes
are not covered by warranty.

WARNINGS

- This page contains an important warning to

prevent injury or death. Please read carefully!

PRECAUTIONS

- Following are important precautions to

prevent damage to unit or merchandise. Read carefully!

WIRING DIAGRAM



Each case has its own wiring diagram folded and in its
own packet.



Wiring diagram placement may vary; it may be placed
near ballast box, field wiring box, raceway cover, or
other related location.

OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / PLUGS / WIRING DIAGRAM

CAUTION! LAMP REPLACEMENT GUIDELINES

LED lamps reflect specific size, shape and overall design.

Any replacements must meet factory specifications.

Fluorescent lamps have been treated to resist breakage and

must be replaced with similarly treated lamps.

CAUTION

CAUTION! POWER CORD AND PLUG MAINTENANCE

Risk of electric shock. If cord or plug becomes damaged,

replace only with cord and plug of same type.

WARNING

Risk of electric shock.

Disconnect ALL ELECTRICAL SOURCES before servicing.

WARNING

ELECTRICAL

HAZARD

CAUTION! GFCI BREAKER USE REQUIREMENT

If N.E.C. (National Electric Code) or your local code

requires GFCI (Ground Fault Circuit Interrupter) protection,

you MUST use a GFCI breaker in lieu of a GFCI receptacle.

COMPLIANCE

This equipment MUST be installed in compliance with

all applicable NEC, federal, state and local

electrical and plumbing codes.

ATTENTION

CONTRACTORS

Содержание CDR4694























Результаты поиска

Содержание CDR4694

Отзывы:

Похожие инструкции для CDR4694

Бренды по названию

Популярные бренды

Structural Concepts CDR4694, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CDR4694

Отзывы:

Похожие инструкции для CDR4694

Бренды по названию

Популярные бренды