Storm AXS Strikemaster Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 22

background image

AXS Strikemaster

Engineering Manual

AXS Strikemaster Programming and Operation Manual May 2013 Page 8 of 22

For more information visit

www.storm-interface.com

© Copyright Storm Interface. 2013. All rights reserved

Operation and Basic Programming

Read this manual carefully before attempting to install, program or operate the STORM AXS Strike Master
Keypad. After installation the Command Summary Chart at the back of this manual can be used as a quick
reference to programming and operating command sequences.

Introduction and Factory Default Settings

Storm AXS Strike Master Keypads provide comprehensive access control for all outdoor and indoor
locations. Door / system status is indicated by a high intensity LED light source and an audible sounder.
Storm AXS Strike Master Keypads are specified to survive in different service environments, ranging from
exposed unsupervised public locations to general service indoor applications. Keypads in the Storm AXS
Strike Master range are dimensionally and electrically interchangeable. This allows users, entering codes at
both outdoor or indoor access points, to establish and maintain familiarity with the keypad features.

Summary of Features

• Up to 50 user programmable entry codes
• Entry Code indexing system provides a
directory of authorised code holders and
permits secure allocation and re-allocation
of entry codes
• 4, 5, or 6 digit entry codes
• One or two door control
• Anti-tamper alarm
• Entry code entered under duress alarm
• Hidden entry code feature
• Forced door alarm

• Timed strike or latching door operation
• Timed lock out for repeated invalid code
input
• Remote exit switch facility
• Fail (open) Fail (closed) option
• All weather resistant
• Two protection levels
– anti vandal keypad for unsupervised
public, outdoor locations
– robust keypad for
regular outdoor / indoor locations

The STORM AXS Strike Master Keypad is supplied with the following factory configured defaults

FEATURE

FACTORY

SET

DEFAULT

‘Engineer’s’ code

111111 (For security, change default engineer’s code on installation)

Door 1 ‘Strike Time’

5 seconds (always resets to 5 sec on power up)

Door 2 ‘Strike Time’

5 seconds (always resets to 5 sec on power up)

Invalid code Penalty time

15 seconds

Relay 2 output

Set in ‘Alarms Mode’

Relay 2 Configuration

Relay Output set ‘normally open’

Door Sensor

Bridged. Remove wire bridge to enable this feature

«
...
6
7
8
9
10
...
»

Содержание AXS Strikemaster























Отзывы:

Нет отзывов

Похожие инструкции для AXS Strikemaster

Бренд: JBL Страницы: 4

Бренд: L-Acoustics Страницы: 38

Бренд: L-Acoustics Страницы: 31

Бренд: L-Acoustics Страницы: 24

Бренд: L-Acoustics Страницы: 201

Water Jet Lightning

Бренд: Oase Страницы: 28

Бренд: Oase Страницы: 9

Бренд: Waters Страницы: 116

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 16

Mobile Multimedia AM/FM/DVD Receiver VM9311

Бренд: Jensen Страницы: 90

Бренд: Pure Acoustics Страницы: 1

Бренд: Viking Страницы: 4

Бренд: AGFEO Страницы: 20

Link Door Phone

Бренд: Linkcom Страницы: 31

Бренд: Laser Страницы: 3

BNI PNT-507-005-Z040

Бренд: Balluff Страницы: 2

Бренд: NAIM Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды