Störk-Tronic TRT252-31.34 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 22

Störk-Tronic TRT252-31.34 Скачать руководство пользователя страница 22

Order No.: 199927

Technical data of TRT252-31.34

Input
E1:

External potential-free switching input, function see parameter b0.

Measuring input

F1:

Resistance thermometer PTC, counter temperature, plug colour white

F2:

Resistance thermometer PTC, evaporator sensor, plug colour red

Measuring range: -55 °C...+99°C

F3:

Current input 0-20mA

Measuring accuracy: 0.5 % of scale range, without sensor

Outputs

S1:

Triac, 4A, 230V ( 0...100 % linear)

with 4A T fuse, potential-free, ventilator

K1:

Relay, 16A 250V, without fuse, see parameter U1

K2:

Relay, 16A 250V, with 6.3A T fuse, see parameter U2

K3:

Relay, 16A 250V, with 6.3A T fuse, see parameter U3

K4:

Relay, 16A 250V, with 6.3A T fuse, see parameter U4

K5:

Relay, 16A 250V, with 6.3A T fuse, see parameter U5

Relays K1 up to K5 are potential-afflicted
Additional buzzer, 85dB

Display

One 3-digit LED-Display, height 13mm, for temperature display, colour red, including the switching
condition display for the output relays
One 4-digit LED-Display, height 13 mm, colour red, for internal real time clock
8 LEDs, for status display

LON communication interface

shielded 2-wire line, Twisted Pair, 78kBaud, not polar, maximum cable length 100m
Interface driver: FTT10A, galvanically separated.
The network can be installed in arbitrary topology.

Power supply

230V 50Hz, max. 10VA

Ambient conditions:

Storage temperature:

-20...+70°C

Operating temperature:

0...55°C

Relative humidity:

max. 75%, without dew

Enclosure

Front IP63, IP00 from back

Installation data

Unit is to be installed in an instrument panel.
Front size:

252 x 72 mm

Panel cut-out:

242.5 x 50.5 mm

Installation depth:

ca. 200 mm

«
...
20
21
22

Содержание TRT252-31.34























Отзывы:

Нет отзывов