manualshive.com logo in svg

Stober PROFINET SD6, Руководство по эксплуатации

Поделиться
Скачать
Stober PROFINET SD6 Скачать руководство пользователя страница 13

STOBER

5 | PN6 communication module

11/2019 | ID 442710.03

13

5

PN6 communication module

The drive controllers of the SD6 series are connected to a higher-level controller using PN6 communication modules, which
provide the necessary fieldbus interfaces.

The communication modules match the PROFINET IO standard and enable cyclical and acyclical data exchange between the
drive controllers and the controller.

5.1

Installation

Installation work is permitted only when no voltage is present. Observe the five safety rules.

Note the minimum clearances listed in the technical data during installation in order to prevent the drive controller from
overheating.

Protect the device against falling parts (wire scraps, wires, pieces of metal, etc.) during installation or other work in the
control cabinet. Parts with conductive properties may result in a short circuit or failure inside the drive controller.

Remove the additional covers before commissioning so that the drive controller does not overheat.

DANGER!

Electrical voltage! Risk of fatal injury due to electric shock!

▪

Always switch off all power supply voltage before working on the devices!

▪

Note the discharge time of the DC link capacitors in the general technical data. You can only determine the absence
of voltage after this time period.

ATTENTION!

Damage to property due to electrostatic discharge!

Take appropriate measures when handling exposed circuit boards, e.g. wearing ESD-safe clothing.

Do not touch contact surfaces.

Tool and material

You will need:

§

A TORX screwdriver TX10

§

The cover and screws included with the communication module

Installation

1.

Unscrew the fastening screw of the dummy cover on top of the drive controller and remove the cover.

2.

Slide the communication module on the guide rails into the drive controller.

3.

Press on the module in order to push the pin contacts into the box header.

4.

Set the tabs of the cover included with the communication module in front in the notch at an angle.

5.

Place the cover on the drive controller so that the tabs lie under the edge.

6.

Attach the cover using both screws.

Содержание PROFINET SD6
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды