Still ECU-SF-20 Скачать руководство пользователя страница 35

Страница: 35 / 92

Knowledge of the Truck

Operator step plate

The operator step plate (1) has three positions;
Position "A" = step plate raised
This position is used when the truck is oper-

ated with the driver on the ground and the side

panels are open; the truck can move in this

position, while its drive speed is electronically

limited to approximately 6 km/h.

NOTE

Traction is blocked when the side panels are

closed.

Position "B" = step plate on stand-by

Traction is constantly blocked in this position.
Position "C" = step plate in working position

with the operator on board
This position is automatic when the operator

steps onto the step plate (1). Truck traction

is constantly enabled in this position and the

speed of the truck varies in relation to the

position of the side panels:
• With the side panels closed, the truck can

reach its maximum speed.

• With the side panels open, the truck’s speed

is electronically limited to ~ 6 km/h.

Moving the step plate

1983

To raise or lower the step plate, manually

move the plate in the direction of the (2) arrow

to raise it and in the direction of the (3) arrow

to lower it.

45378043402 [EN]

Содержание ECU-SF-20





























































































Результаты поиска

Содержание ECU-SF-20

Отзывы:

Still ECU-SF-20, Оригинальное руководство пользователя, Страница: 35 / 92

Результаты поиска

Содержание ECU-SF-20

Отзывы: