Still ECU-SF-20 Скачать руководство пользователя страница 34

Страница: 34 / 92

Knowledge of the Truck

Operator side panels

Position "A" = side panels open

This position is used when the truck is oper-

ated with the driver on the ground and the step

plate is raised, or with the driver standing on

the step plate with automatic speed reduction.

Opening the side panels

To open the side panels (1) and pass from

position "C" to position "A" proceed as follows:
• Press the lock pin (2) until it reaches the

stopper and at the same time gently push

one of the side panels (1), turning it to

position "A".

NOTE

When in position "A", the side panels are

automatically locked by the lock cylinder

in order to prevent them from accidentally

closing.

Closing the side panels

To close the side panels (1) and pass from

position "A" to position "C" proceed as follows:
Press the lock pin (2) until it reaches the

stopper and at the same time gently push

one of the side panels (1), turning it to position

"C".

NOTE

Traction of the truck is enabled when side

panels "C" are closed and side panels "A"

are open and properly locked with the lock

pin (2). If the side panels are not properly

locked by the lock pin (2), any movement of

the truck will be blocked. The position of the

side panels should be changed when the truck

is stationary.

DANGER

Do not press the lock pin (2) when the truck is

moving.
Do not sit on the side panels.

45378043402 [EN]

Содержание ECU-SF-20





























































































Результаты поиска

Содержание ECU-SF-20

Отзывы:

Still ECU-SF-20, Оригинальное руководство пользователя, Страница: 34 / 92

Результаты поиска

Содержание ECU-SF-20

Отзывы: