Stihl MS 361 Скачать руководство пользователя

Страница: 27 / 44

NOTICE

Always slacken off the chain again after finishing

work. The chain contracts as it cools down. If it is

not slackened off, it can damage the crankshaft

and bearings.

17.3.1

Short-term storage

Wait for engine to cool down. Keep the machine

with a full tank of fuel in a dry place, well away

from sources of ignition, until you need it again.
17.3.2

Long-term storage

See "Storing the machine"

18 Oil Quantity Control

Adjustable flow oil pump is a special option.
Different quantities of oil are required for different

bar lengths, types of wood and cutting techni‐

ques.

001BA157 KN

Use the adjusting screw (1) (on underside of

machine) to vary the oil feed rate as required.
Ematic position (E), medium oil flow rate –

► turn the adjusting screw to "E" (Ematic posi‐

tion).

To increase oil feed –

► turn the adjusting screw clockwise.
Turn reduce oil feed –

► turn the adjusting screw counterclockwise.

NOTICE

The chain must always be wetted with a film of

lubricant.

19 Taking Care of the Guide

Bar

143BA026 KN

► Turn the guide bar over – every time you

sharpen the chain and every time you replace

the chain – this helps avoid one-sided wear,

especially at the nose and underside of the

bar.

► Regularly clean the oil inlet hole (1), the oil‐

way (2) and the bar groove (3)

► Measure the groove depth – with the scale on

the filing gauge (special accessory) – in the

area used most for cutting

Chain type

Chain pitch

Minimum

groove

depth

Picco

1/4" P

4.0 mm

Rapid

1/4“

4.0 mm

Picco

3/8" P

5.0 mm

Rapid

3/8“; 0.325“

6.0 mm

Rapid

0.404“

7.0 mm

If groove depth is less than specified:

► Replace the guide bar
The drive link tangs will otherwise scrape along

the bottom of the groove – the cutters and tie

straps will not ride on the bar rails.

20 Air Filter System

The air filter system can be adapted to suit differ‐

ent operating conditions by installing a choice of

filters. Changing the filter is quick and simple.
The saw comes standard with either a fabric filter

or a fleece filter.

20.1

Fabric filter

For normal operating conditions and winter oper‐

ation.

18 Oil Quantity Control

English

0458-212-0121-C

Содержание MS 361













































Результаты поиска

Содержание MS 361

Отзывы:

Похожие инструкции для MS 361

Бренды по названию

Популярные бренды

Stihl MS 361, Инструкция по эксплуатации

Результаты поиска

Содержание MS 361

Отзывы:

Похожие инструкции для MS 361

Бренды по названию

Популярные бренды