Stihl MS 361 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 44

Stihl MS 361 Скачать руководство пользователя страница 18

9.3

Storing fuel mixture

Store in approved safety fuel canisters only in a

dry, cool and secure place protected against light

and sunlight.
Fuel mixture deteriorates with age – mix only as

much as needed for a few weeks. Do not store

fuel mixture for longer than 30 days. The fuel

mixture can become unusable more quickly if

exposed to light, sunlight or low or high tempera‐

tures.
STIHL MotoMix however can be stored for up to

5 years without any problems.

► Shake the canister containing the fuel mixture

thoroughly before refueling

WARNING

Pressure may have built up in the canister –

open it carefully.
► The fuel tank and the canister in which fuel

mixture is stored should be cleaned thoroughly

from time to time

Residual fuel and the liquid used for cleaning

must be disposed of in accordance with regula‐

tions and without harming the environment!

10 Fueling

10.1

Preparing the machine

001BA229 KN

► Before fueling, clean the cap and the area

around it to ensure that no dirt falls into the

fuel tank

► Always position the machine so that the cap is

facing upwards

10.2

Opening

001BA236 KN

► Raise grip to vertical position.

001BA232 KN

► Turn the cap counterclockwise (about a quar‐

ter turn).

001BA234 KN

Marks on tank cap and fuel tank must line up.

001BA237 KN

► Remove the tank cap.

English

10 Fueling

18

0458-212-0121-C

«
...
16
17
18
19
20
...
»

Содержание MS 361













































Отзывы:

Нет отзывов