Stihl MS 361 Скачать руководство пользователя страница 28

Страница: 28 / 44

20.2

Fleece filter

For dry and very dusty work areas.

21 Cleaning the Air Filter

21.1

If there is a noticeable loss of

engine power

21.1.1

Removing the carburetor box cover

► Move the Master Control lever to stop posi‐

tion (0).

213BA009 KN

► Loosen the twist lock (1) in the direction of the

arrow.

► Remove the carburetor box cover (2).
21.1.2

Removing the air filter

► Clean away loose dirt from around the filter.

NOTICE

To avoid damaging the filter, do not use tools for

removing and installing the air filter.
► Remove the filter.
21.1.3

Cleaning the air filter

► Knock the filter out on the palm of your hand

or blow it clear with compressed air from the

inside outwards.

If filter is caked with dirt:

► Wash the filter in STIHL special cleaner (spe‐

cial accessory) or a clean, non-flammable sol‐

ution (e.g. warm soapy water) and then dry.

NOTICE

Do not use a brush to clean the fleece filter.
► Always replace damaged filters.

21.1.4

Installing the air filter

► Place the filter (3) in position (arrows).

► Fit the carburetor box cover.

22 Adjusting the Carburetor

22.1

General Information

The carburetor comes from the factory with a

standard setting.
This setting provides an optimum fuel-air mixture

under most operating conditions.
With this carburetor it is only possible to correct

the adjusting screws within fine limits.

22.2

Standard Setting

► Shut off the engine.

► Check the air filter and clean or replace if nec‐

essary.

► Check the spark arresting screen (not in all

models, country-specific) in the muffler and

clean or replace if necessary.

213BA015 KN

► Turn high speed screw (H) counterclockwise

as far as stop (no more than 3/4 turn).

► Turn the low speed screw (L) clockwise as far

as stop, then turn it back a 1/4 turn.

22.3

Adjusting Idle Speed

► Carry out the standard setting.

► Start and warm up the engine.
22.3.1

Engine stops while idling

► Set the low speed screw (L) to 1/4 turn open.

English

21 Cleaning the Air Filter

0458-212-0121-C

Содержание MS 361













































Результаты поиска

Содержание MS 361

Отзывы:

Похожие инструкции для MS 361

Бренды по названию

Популярные бренды

Stihl MS 361, Инструкция по эксплуатации

Результаты поиска

Содержание MS 361

Отзывы:

Похожие инструкции для MS 361

Бренды по названию

Популярные бренды