manualshive.com logo in svg

Stihl HL 92, Инструкция по эксплуатации

Поделиться
Скачать
Stihl HL 92 Скачать руководство пользователя страница 21

NOTICE

Do not operate your machine with dull or dam‐

aged cutting blades. This may cause overload

and will give unsatisfactory cutting results.

18 Storing the Machine

If out of use for periods of about 30 days or lon‐

ger

► Drain and clean the fuel tank in a well ventila‐

ted area.

► Dispose of fuel properly in accordance with

local environmental requirements.

► If a manual fuel pump is fitted: Press the man‐

ual fuel pump at least 5 times.

► Start the engine and run it at idling speed until

it stops.

► Clean the cutting blades, check condition and

spray them with STIHL resin solvent.

► Fit the blade scabbard.

► Thoroughly clean the machine.

► Store the machine in a dry and secure location

Keep out of the reach of children and other

unauthorized persons.

19 Inspection and Mainte‐

nance by User

19.1

Throttle Cable

19.1.1

Checking adjustment of throttle cable

Error: Engine speed increases when only the

throttle trigger is pulled.

2

1191BA023 KN

1

► Start the engine.

► Pull the throttle trigger (1) – do not press down

the throttle trigger lockout (2).

If the engine speed increases or if the cutting

blades run, the throttle cable has to be adjusted.

► Shut off the engine.

► Have throttle cable adjusted by your dealer.

STIHL recommends an authorized STIHL

servicing dealer.

19.2

Spark arresting screen in muf‐

fler

WARNING

To reduce the risk of fire caused by hot particles

escaping from the machine, never operate the

machine without a spark arresting screen, or with

the spark arresting screen damaged. Do not

modify the muffler or spark arresting screen.

NOTICE

According to the law or regulations in some

countries or federal states, certain operations

may only be carried out if a properly serviced

spark arresting screen is provided.

If the engine is down on power, check the spark

arresting screen in the muffler.

► Wait for the muffler to cool down

1191BA017 KN

1

2

► Undo screw (1)

► Lift the spark arresting screen (2) and pull it

out.

► Clean the spark arresting screen. If the screen

is damaged or heavily carbonized, fit a new

one

► Refit the spark arresting screen

► Insert and tighten the screw

20 Inspections and Mainte‐

nance by Dealer

20.1

Maintenance work

STIHL recommends that all maintenance and

repairs be carried out by STIHL dealers.

18 Storing the Machine

English

0458-519-8321-D

21

Содержание HL 92





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды