manualshive.com logo in svg

Stihl HL 92, Инструкция по эксплуатации

Поделиться
Скачать
Stihl HL 92 Скачать руководство пользователя страница 13

7.2

Open the tank cap.

0208BA020 KN

► Turn the cap counterclockwise until it can be

removed from the tank opening.

► Remove the cap.

7.3

Filling up with fuel

Take care not to spill fuel while fueling and do

not overfill the tank.
STIHL recommends you use the STIHL filler noz‐

zle for fuel (special accessory).

► Fill up with fuel.

7.4

Close the tank cap.

0208BA021 KN

► Place the cap in the opening.

► Turn the cap clockwise as far as stop and

tighten it down as firmly as possible by hand.

8

Adjusting the Cutter Bar

8.1

Angle Adjuster - 145°

0000-GXX-1683-A0

145°

The angle of th cutter bar can be adjusted

upwards in 4 stages from 0° (straight) to 55°, and

downwards in 7 stages from 0° to 90° (right

angle facing down). There are therefore 12 pos‐

sible working positions.

WARNING

To reduce the risk of injury, carry out the adjust‐

ment only when the cutting blades are at a

standstill – engine at idle speed.

WARNING

The gearbox gets hot during operation. To

reduce the risk of burn injury, do not touch the

gearbox.

WARNING

To reduce the risk of injury, never touch the

blades while making adjustments.

8 Adjusting the Cutter Bar

English

0458-519-8321-D

13

Содержание HL 92





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды