Stihl HL 92 Скачать руководство пользователя | Manualshive

Страница: 11 / 28

background image

2

A

0000-GXX-1680-A0

► Align the loop handle (2) and move it to the

most comfortable position (recommended:

about 20 cm).

► Tighten down the screws firmly.

5.2

Mounting the Gearbox

11

10

10

5

0000-GXX-1681-A0

► Loosen the clamp screws (10).

► Push the gearbox (11) onto the drive tube (5),

turn the gearbox (11) back and forth as neces‐

sary.

11

12

0000-GXX-1682-A0

Once the end of the drive tube is inserted

beyond the slot in the clamp (12):

► Push the gearbox (11) fully home as far as

stop.

► Tighten down the clamp screws moderately.

► Line up the gearbox (11) with the powerhead.

► Tighten down the clamp screws firmly.

6

Fuel

The engine requires a mixture of gasoline and

engine oil.

WARNING

Avoid direct skin contact with fuel and breathing

in of gasoline fumes.

6.1

STIHL MotoMix

STIHL recommends using STIHL MotoMix. This

pre-blended fuel is free of benzene and lead, is

distinguished by a high octane rating, and

always provides the proper mixing ratio.
STIHL MotoMix uses STIHL HP Ultra two-stroke

engine oil for optimum engine life.
MotoMix is not available in all markets.

6 Fuel

English

0458-519-8321-D

11

«
...
9
10
11
12
13
...
»

Содержание HL 92





























Отзывы:

Нет отзывов

Похожие инструкции для HL 92

Бренд: Varec Страницы: 74

Бренд: PAIDI Страницы: 48

Бренд: Gardena Страницы: 13

Бренд: Raven Страницы: 27

Бренд: Raven Страницы: 79

Бренд: Raven Страницы: 88

Бренд: DAKO Страницы: 25

Бренд: 3M ESPE Страницы: 50

Бренд: Panlux Страницы: 2

Бренд: W&H Med Страницы: 122

Бренд: Tarmo Страницы: 4

Бренд: ultraMEDIC Страницы: 28

NOVACAT X8 COLL

Бренд: Pottinger Страницы: 91

Бренд: Duracell Страницы: 2

Бренд: XPOtool Страницы: 10

Бренд: REV Ritter Страницы: 11

Бренд: Denon Страницы: 84

Бренд: iGuzzini Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды