Stihl HL 92 Скачать руководство пользователя

Страница: 16 / 28

10.1.1

Function of Stop Switch and Ignition

System

The ignition is switched off and the engine stop‐

ped when the stop switch is pressed. The stop

switch returns automatically to the Run position

when it is released: The ignition is switched on

again after the engine stops – the engine is then

ready to start.
10.1.2

Function of Throttle Set Wheel

0208BA067 KN

The throttle set wheel (4) enables the travel of

the throttle trigger to be preset anywhere

between idle and full throttle.

–

Turn throttle set wheel (4) in direction of – to

reduce throttle trigger travel and maximum

engine speed.

–

Turn throttle set wheel (4) in direction of + to

increase throttle trigger travel and maximum

engine speed.

–

It is possible to override the preset stop and

open the throttle wide by pulling the throttle

trigger firmly – the preset stop remains unaf‐

fected. The original setting is restored when

the throttle trigger is released.

10.2

Starting the Engine

0000-GXX-5224-A0

► Press the manual fuel pump bulb (5) at least

five times – even if the bulb is already filled

with fuel.

Cold engine (cold start)

0000-GXX-5475-A0

► Turn choke knob (6) and then push it in at

Also use this setting if the engine has been run‐

ning but is still cold.

–

Turn throttle set wheel in direction of + as far

as stop.

Hot engine (hot start)

► Choke knob (6) remains in

position.

10.2.1

Cranking

1191BA014 KN

► Place the machine on the ground: It must rest

securely on the engine support and the gear‐

box housing.

► On units with an adjustable cutter bar and

defined transport position: Set the cutter bar to

the straight (0°) position.

► If fitted: Remove blade scabbard from the cut‐

ting blades.

To reduce the risk of accidents, check that the

cutting blades are not touching the ground of any

other obstacles.

► Make sure you have a firm footing, either

standing, stooping or kneeling.

► Hold the machine firmly on the ground with

your left hand and press down – do not touch

the throttle trigger, lockout lever or stop switch.

English

10 Starting / Stopping the Engine

0458-519-8321-D

Содержание HL 92





























Результаты поиска

Содержание HL 92

Отзывы:

Похожие инструкции для HL 92

Бренды по названию

Популярные бренды

Stihl HL 92, Инструкция по эксплуатации

Результаты поиска

Содержание HL 92

Отзывы:

Похожие инструкции для HL 92

Бренды по названию

Популярные бренды