Stihl FR 480 C страница 23 Скачать руководство пользователя

Страница: 23 / 44

FR 480 C

English

STIHL SuperCut 20-2,
STIHL AutoCut 25-2,
STIHL AutoCut C 25-2,
STIHL AutoCut 30-2,
STIHL TrimCut 31-2,
STIHL FixCut 25-2,
STIHL PolyCut 20-3

Unscrew the mowing head
clockwise.

STIHL FixCut 25-2 (early version)

Use the combination wrench to
loosen and unscrew the mounting
nut clockwise from the output shaft.

Adjusting Nylon Line

STIHL SuperCut

Fresh line is advanced automatically if
remaining line is still

at least 6 cm

long.

The blade on the deflector trims surplus
line to the correct length.

STIHL AutoCut

Hold the rotating mowing head
above the ground – tap it on the
ground once – about

3 cm

fresh line

is advanced.

The blade on the deflector trims surplus
line to the correct length – avoid tapping
the mowing head more than once at a
time.

Line feed operates only if

both

lines still

have a minimum length of

2.5 cm

All other mowing heads

Refer to the instructions supplied with
the mowing head.

Replacing Nylon line or Cutting
Blades

Refer to the instructions supplied with
the mowing head.

Mounting Metal Cutting Attachments

The

skirt and line limiting blade are

not required

on the mowing attachment

deflector for grass cutting blades
230-2 (1), 230-4 (2), 230-8 (3),
250-40 Spezial (4) or the brush knife (5)
– see "Mounting the Deflector".

Lay your brushcutter on its back with the
cutting attachment mounting face
pointing up: The cutting edges of (1), (2)
and (5) may point in either direction. The
cutting edges of (3) and (5) must point
clockwise.

Place the cutting attachment (6) on
the thrust plate (7).

Fit the thrust washer (8) and rider
plate (9) on the shaft (10).

Block the shaft.

Use the combination wrench (12) to
screw the mounting nut (11) on to
the output shaft counterclockwise
and tighten it down firmly.

If the mounting nut turns too
freely, fit a new one.

To reduce the risk of injury, always
shut off the engine before
adjusting the mowing line by
hand.

681BA045 KN

Direction of rotation is indicated by
an arrow on the inside of the
deflector.

Collar (see arrow) must engage
the cutting attachment's mounting
hole.

Содержание FR 480 C













































Результаты поиска

Содержание FR 480 C

Отзывы:

Похожие инструкции для FR 480 C

Бренды по названию

Популярные бренды

Stihl FR 480 C, Инструкция по эксплуатации

Результаты поиска

Содержание FR 480 C

Отзывы:

Похожие инструкции для FR 480 C

Бренды по названию

Популярные бренды