Stihl 1139 Series Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 48

Stihl 1139 Series Скачать руководство пользователя страница 38

mark) is lowered at the same time as the depth

gauge of the cutter.

WARNING

The rest of the humped drive link must not be

filed; otherwise, this could increase the tendency

of the chain saw to kick back.

689BA051 KN

► Rework the depth gauge so that it is flush with

the file gauge

689BA044 KN

► Afterwards, dress the leading edge of the

depth gauge parallel to the service mark (see

arrow) – when doing this, be careful not to fur‐

ther lower the highest point of the depth gauge

WARNING

Depth gauges that are too low increase the kick‐

back tendency of the chain saw.

689BA052 KN

► Lay the file gauge on the saw chain – the high‐

est point of the depth gauge must be flush with

the file gauge

► After sharpening, clean the saw chain thor‐

oughly, removing any filings or grinding dust –

lubricate the saw chain thoroughly

► In the event of extended periods of disuse,

store saw chains in cleaned and oiled condi‐

tion

English

29 Maintaining and Sharpening the Saw Chain

38

0458-533-0121-E

«
...
36
37
38
39
40
...
»

Содержание 1139 Series

















































Отзывы:

Нет отзывов