Stihl 1139 Series Скачать руководство пользователя страница 27

Страница: 27 / 48

Simultaneously pressing the throttle trigger lock‐

out and blipping the throttle trigger causes the

master control lever to jump from the warm

start

position to the operating position

To switch off the engine, set the master control

lever to Stop 0.
18.2.1

Position choke shutter closed

–

if the engine is cold

–

if the engine stalls during opening of throttle

after starting

–

If the fuel tank has run empty (engine stalled

out)

18.2.2

Position starting acceleration

–

if engine is warm (once the engine has been

running for approx. one minute)

–

When the engine has turned over for the first

time

–

after ventilation of the combustion chamber, if

the engine was flooded

18.3

Fuel pump

Press the fuel pump bulb several times – even if

it is still full of fuel:

–

When starting for the first time

–

If the fuel tank has run empty (engine stalled

out)

18.4

Holding the chain saw

There are two ways to hold the chain saw during

starting.

18.4.1

On the ground

143BA018 KN

► Place the chain saw securely on the ground –

assume a steady stance – the saw chain must

not touch any objects and also must not touch

the ground

► With the left hand on handlebar, press the

chain saw firmly against the ground – thumb

wrapped around the handlebar

► Place your right foot through the rear handle

18 Starting / Stopping the Engine

English

0458-533-0121-E

Содержание 1139 Series

















































Результаты поиска

Содержание 1139 Series

Отзывы:

Бренды по названию

Популярные бренды

Stihl 1139 Series, Инструкция по эксплуатации

Результаты поиска

Содержание 1139 Series

Отзывы:

Бренды по названию

Популярные бренды