Stieber Clutch RSXM Series Скачать руководство пользователя страница 14

 

 

Stieber Clutch  

 

Page 14/21 

M1016E_0

 

Assembly and maintenance manual

 

 

6.3 Assembly 

 

WARNING

 

Risk of injury due to incorrect assembly! 

Faulty installation and maintenance can cause severe property 
damage and personal injury. 
Installation, maintenance and repair work may only be performed 
by personnel with the requisite training and expertise. 

 

 

WARNING

 

Risk of injury due to moving components! 

Rotating driven components can cause the most severe injuries. 
Therefore, during operation: 

  It is strictly forbidden for persons to loiter in the danger zone 

or in its immediate vicinity. 

  Do not disable, render unusable or circumvent safety 

equipment and / or safety functions. 

Prior to entering the danger zone: 

  Switch off the power supply and secure it against being 

switched on again. 

  Wait for lagging components to come to a standstill. 

 

 

CAUTION

 

Risk of injury due to falling components! 

The outer race or inner race can fall down if the transportation lock 
has been removed. 
Fasten the outer / inner race axially. 

 

Procedural steps : 

  Lift up the one-way clutch using suitable lifting gear and push it onto the oiled 

machine shaft 

  Remove the cable clip 

  Fasten the one-way clutch axially on the machine shaft 

  Center the outer race in the torque-supporting machine element 

 

NOTE

 

Screw qualities 12.9 must not be used! 

  Secure the outer race in the torque-supporting machine element with the 

appropriate fixing screws (e.g. as per standard DIN EN ISO 4762) and with screw 
quality 10.9 or 8.8; tightening torque (see Table Tightening torque) 

 

Tightening torque

 [Nm] 

Size 

8.8 

10.9 

M6 

10 14 

M8 

25 

34 

M10 

48 68 

Table:  Tightening torque (

according VDI 2230 Sheet1, µ=0.12 metric standard thread) 

Содержание RSXM Series






















Отзывы: