STIEBEL ELTRON SOM 8 PLUS Скачать руководство пользователя страница 7

Страница: 7 / 84

2.3

Data communication / Bus

the controller is equipped with the

VBus

for data

transfer with and energy supply to external modu-

les. the connection is carried out at the two termi-

nals marked VBus and GnD (any polarity).

the terminals s13 to s15 can be used as impulse in-

puts for V40 flowmeters or as inputs for Fs08 flow

switches.
V40 flowmeters can be connected to the terminals

s13 / V40 to s15 / V40 and GnD (either polarity).
Connect the irradiation sensor

CS10

to the termi-

nals Cs10 and GnD with correct polarity. to do so,

connect the cable marked GnD to the GnD common

terminal block, the cable marked Cs to the terminal

marked Cs10.

The terminals marked

pWm are control outputs for

high-efficiency pumps.
In the In-/outputs menu, relays can be allocated to

the pWm outputs.
Connect the

FlowRotor

to the input marked Flow-

rotor.
Connect the

analog Grundfos Direct Sensors

™ to

the inputs GDsa1 and GDsa2.
Connect the

digital

Grundfos Direct Sensors

™ to

the GDsD1 and GDsD2 inputs.
the controller is supplied with power via a mains

cable. the power supply of the device must be

100 ... 240 V~ (50 ... 60Hz).

the

mains connection

is at the terminals:

neutral conductor n

Conductor l

Conductor l' (l' is not connected with the mains

cable. l' is a fused contact permanently carrying

voltage)
protectiv earth conductor (common terminal

block)

Note:

For more information about accessories,

see page 80.

WARNING!

Electric shock!

l‘ is a fused contact permanently

carrying voltage

Always disconnect the

controller from power supply

before opening the housing!

295931-36390-8667 SOM 8 plus_en.indb 7

20.10.2011 13:14:21

Содержание SOM 8 PLUS





















































































Результаты поиска

Содержание SOM 8 PLUS

Отзывы:

STIEBEL ELTRON SOM 8 PLUS, Руководство по установке, Страница: 7 / 84

Результаты поиска

Содержание SOM 8 PLUS

Отзывы: