STIEBEL ELTRON SOM 8 PLUS Скачать руководство пользователя страница 37

Страница: 37 / 84

the Cs bypass function is a different possibility to

activate the collector circuit. to enable the use of the

Cs bypass function, a Cs10 irradiation sensor has to

be connected.
When the Cs bypass function is activated, the irra-

diation value is the switch-on condition for the col-

lector circuit.
the relay remains switched on if the irradiation val-

ue is exceeded for the delay time. When solar load-

ing begins or the irradiation value remains below

the switch-on value for the delay time, the relay is

switched off.
When the

Stmax off

option is activated, collector

circuit activation is suppressed as long as all store

temperatures are above their respective maximum

temperatures.

CS bypass

Solar / Opt. functions / Add new function... / CS bypass

adjustment channel

Description

adjustment range / selection Factory setting

Collector

Collector field

system dependent

Irrad.

switch-on irradiation

100 ... 500 W / m²

200 W / m²

Delay

Delay time

10 ... 300 s

120 s

stmax off

stmax switch-on suppression

Yes, no

Yes

Funct.

activation / Deactivation

activ., Deactivated

Deactivated

295931-36390-8667 SOM 8 plus_en.indb 37

20.10.2011 13:14:38

Содержание SOM 8 PLUS





















































































Результаты поиска

Содержание SOM 8 PLUS

Отзывы:

STIEBEL ELTRON SOM 8 PLUS, Руководство по установке, Страница: 37 / 84

Результаты поиска

Содержание SOM 8 PLUS

Отзывы: