STIEBEL ELTRON SOM 8 PLUS Скачать руководство пользователя страница 46

Страница: 46 / 84

Heat dump

the heat dump function can be used to direct excess

heat generated by strong solar irradiation to an ex-

ternal heat exchanger (e. g. fan coil) in order to pre-

vent the collectors from overheating.
the allocated relay is energised with 100 %, if the col-

lector temperature reaches the adjusted switch-on

temperature. If the collector temperature falls by 5 K

below the adjusted collector overtemperature, the

relay will be switched off.
If one of the store temperatures exceeds its respec-

tive maximum temperature by more than 5 K while

the heat dump function is active, the function is

deactivated and an error message appears. If the

store temperature falls below the maximum store

temperature again, the heat dump function is re-

leased.

Note:

the switch-on collector temperature is

blocked against the emergency switch-off

temperature by 10 K [20 °ra].

adjustment channel Description

adjustment range / selection Factory setting

relay

relay selection

system dependent

tcol.

switch-on collector temperature 40 ... 190 °C [104 ... 374 °F]

110 °C [230 °F]

Funct.

activation / Deactivation

activ., Deactivated

Deactivated

Solar / Opt. functions / Add new function... / Heat dump

Relay

Flow rate monitoring

the flow rate monitoring function can be used to de-

tect malfunctions that impede the flow rate and to

switch off the corresponding relay. this will prevent

system damage, e. g. through a dry run of the pump.
If the flow rate monitoring function is activated,

an error message will appear when no flow rate is

detected at the allocated flowmeter after the delay

time has passed. the store being loaded is blocked

for any further loading until the error message has

been ac knowl edged. the next store free for loading

will be loaded instead.
the error message will appear both in the

Status

/ Messages

menu and in the optional function

menu. It can only be acknowledged in the optional

function menu. When the error message is acknow-

ledged, the controller runs a test during which it will

energise the relay and again monitor the flow rate.

adjustment channel Description

adjustment range / selection

Factory setting

sensor

Flow rate sensor selection

Imp1 ... Imp3, Ga1, Ga2, Gd1, Gd2 Imp1

ref. relay

reference relay selection

system dependent

store

sensor selection

system dependent

Funct.

activation / Deactivation

activ., Deactivated

Deactivated

Solar / Opt. functions / Add new function... / Flow rate mon.

295931-36390-8667 SOM 8 plus_en.indb 46

20.10.2011 13:14:42

Содержание SOM 8 PLUS





















































































Результаты поиска

Содержание SOM 8 PLUS

Отзывы:

STIEBEL ELTRON SOM 8 PLUS, Руководство по установке, Страница: 46 / 84

Результаты поиска

Содержание SOM 8 PLUS

Отзывы: