STEYR MO114K33 Скачать руководство пользователя страница 79

Страница: 79 / 118

Trouble Check Chart

– Continued

SYMPTOM

POSSIBLE CAUSE

ACTION

Engine vibrates

Propeller condition

Check for bent, broken, or damaged

propeller Check for weeds on propeller

or sterndrive gearcase. Check for bent

propeller shaft.

Unit injector

See your STEYR MOTORS Marine

dealer.

Engine runs but boat makes

little or no progress

Fouled propeller etc.

Check:

1. Propeller for weeds, remove as

required.

2. Propeller for spun hub, repair or

replace.

3. Hull for excessive marine growth,

clean as required.

Performance loss

1. System error or failure

Check: using diagnostics for errors

or limitations. Engine coolant

temperature; audible and or visual

alarms.

2. Boat overloaded

Reduce load.

3. Boat trim

Distribute boat load evenly. Adjust trim.

4. Excessive water in bilge

Drain bilge.

5. Boat hull condition

See your STEYR MOTORS Marine

dealer.

6. Improper propeller selection

Select proper propeller pitch and

diameter.

7. Fuel incorrect

Fill tank with correct fuel. Check fuel

filter and fuel flow condition.

8. Throttle not fully open

Check throttle command lever for full

travel.

9. Overheating

Check cooling system. Remove debris

from water intake. Check belt tension.

Check condition of impeller.

Check for clogged heat exchanger

tubing (in raw water circuit).

10. Air intake troubles

Check intake air filter.

Check ventilation of engine compartment.

Excessive free play in steering

wheel

Steering cable loose

See your STEYR MOTORS Marine

dealer.

High shift effort

1. Remote control or transom bracket

shift cable

Replace and adjust.

See your STEYR MOTORS Marine

dealer.

2. Remote control binding

See your STEYR MOTORS Marine

dealer.

3. Engine/drive mechanism binding

See your STEYR MOTORS Marine

dealer.

Содержание MO114K33























































































































Результаты поиска

Содержание MO114K33

Отзывы:

Похожие инструкции для MO114K33

Бренды по названию

Популярные бренды

STEYR MO114K33, Руководство по эксплуатации, техническому обслуживанию и гарантии

Результаты поиска

Содержание MO114K33

Отзывы:

Похожие инструкции для MO114K33

Бренды по названию

Популярные бренды