background image

GENERAL INSTALLATION & SERVICE WARNINGS

The control valve, fittings and/or bypass are designed to accommodate minor plumbing
misalignments. There is a small amount of "give" to properly connect the piping but the water
softener is not designed to support the weight of plumbing.
Do not use Vaseline, oils, other hydrocarbon lubricants or spray silicone anywhere. A silicone
lubricant may be used on black "O" Rings, but is not necessary. 

Avoid any type of lubricants, 

including silicone, on red or clear lip seals.
Do not use pipe dope or other sealants on threads.

 Teflon

® 

tape must be used on the threads of the

1" NPT inlet and outlet, the brine line connection at the control valve, and on the threads for the
drain line connection. Teflon

® 

tape is not used on the nut connections or caps because "O" Ring

seals are used. The nuts and caps are designed to be unscrewed or tightened by hand or with the
special plastic Service Wrench, #CV3193. If necessary pliers can be used to unscrew the nut or cap.
Do not use a pipe wrench to tighten nuts or caps. 

Do not place screwdriver in slots on caps and/or

tap with a hammer.

SITE REQUIREMENTS

● water pressure -- 25-100 psi

● current draw is 0.5 amperes

● water temperature -- 33-100°F (0.5-37.7°C)

● the plug-in transformer is for 

● electrical -- 115/120 V, 60 Hz uninterrupted outlet

   dry locations only

● the tank should be on a firm level surface

1. The distance between the drain and the water conditioner should be as short as possible.

2. Since salt must be periodically added to the brine tank, it should be located where it is easily
    accessible.

3. Do not install any water conditioner with less than 10 feet of piping between its outlet and the 
     inlet of a water heater.

4. Do not locate unit where it or its connections (including the drain and overflow lines) will ever be
    subjected to room temperatures under 34°F.

INSTALLATION:

MUNICIPAL INSTALLATION

WELL WATER INSTALLATION

5

Содержание HE Series






















Отзывы: