Stephill DSE 6110 MK3 Скачать руководство пользователя страница 10

Stephill Generators SSDP30-70 -  DSE 6110 Module User Guide

Issue 2

How to Reset the "Service Hours Alarm " Warning

Before Resetting the Service Hours

Resetting the Service Hours

Fig.21

a)  Ensure the 

Service Hours

 screen is visable.

b)  Press and hold the               button. The timer should then reset to the pre-set hours (usaully 500h).

Important Note

The 

Service Hours

 timer can only be reset if the 

Service Hours Warning

 has been activated (reached 0h 0m).

How to Check Which Alarms Have Been Triggered

When an alarm is active, the 

Internal Audible Alarm 

sounds

.

The audible alarm is silenced by pressing the Alarm Mute / Lamp Test               button.

Fig.22

① = Number of active alarms. This is alarm 1 of a total of 2 active alarms.

② = The cause of the alarm.

③ = The type of alarm, e.g. Shutdown.

Firstly you will need to access the 

Service Hours

 in the 

Engine

pages, use the 

Next

 or 

Previous

 buttons until 

across the top of the screen it reads 

Engine

. Then press one of the 

Instrument Scroll

 buttons until 

Service 

Hours

 is displayed at the top of the screen page Fig.21

The 

Service Hours Alarm

 screen is a count down timer, when the timer reaches zero hours a 

Warning Alarm 

will be issued and displayed on the screen. The 

Warning Alarm

 will allow the user to operate the generator 

as normal but the 

Warning Alarm

will be present until a service reset has been performed.

Firstly, ensure an adequate service has been performed on the engine. Refer to the generator handbook or 
check on the 

Service

 section found on;

The 

Service Hours

 should be showing 0h 0m, this idicates that the countdown timer from the last service has 

been achieved. To reset this timer; 

To check which alarm(s) have been triggered, use the 

Next

 or 

Previous

 buttons until across the top of the 

screen it reads 

Alarms

. Fig.20 shows the 

Alarms 

page. To see each individual alarm that is currently 

activated, press one of the 

Instrument Scroll

 buttons to cycle through.

Emergency Stop 

Shutdown 

2/2 

Alarms 

www.stephill-generators.co.uk 

Service Hours 

0h    0m     

Next and Previous 

Instrument Scroll 

③ 

① 

② 

Next and Previous 

Instrument Scroll 

JD/08/18

10

Содержание DSE 6110 MK3



















Отзывы: