Stellar Hearth 4-SS-2-GL Скачать руководство пользователя

Страница: 11 / 37

Page 11

16400-7800 GSS REV D

SINGLE SIDED

SINGLE SIDED FRAMING DIMENSIONS

Model #

FRAMING

WIDTH

HEIGHT

DEPTH

4-SS-2-GL

55-3/4

[1,416]

[1,422]

25-1/32

[636]

5-SS-2-GL

67-3/4

[1,721]

[1,422]

25-1/32

[636]

6-SS-2-GL

79-3/4

[2,026]

[1,422]

25-1/32

[636]

7-SS-2-GL

91-3/4

[2,330]

[1,422]

25-1/32

[636]

4-SS-3-GL

55-3/4

[1,416]

[1,727]

25-1/32

[636]

5-SS-3-GL

67-3/4

[1,721]

[1,727]

25-1/32

[636]

6-SS-3-GL

79-3/4

[2,026]

[1,727]

25-1/32

[636]

7-SS-3-GL

91-3/4

[2,330]

[1,727]

25-1/32

[636]

IMPORTANT:
FIREPLACE IS NOT LOAD-BEARING

Figure 4

4 - FRAMING

IMPORTANT FRAMING NOTES:

FRAMING SHOULD BE BUILT AFTER THE FIREPLACE IS INSTALLED OR EXTRA
CLEARANCE MUST BE PLANNED FOR AT THE INTAKE COLLAR.

THESE DIMENSIONS REPRESENT THE FRAMING DIMENSIONS FOR COMBUSTIBLE
MATERIAL.

NON-COMBUSTIBLE FRAMING AND FINISHING MATERIALS MAY BE USED WITHIN
THESE DIMENSIONS RIGHT UP TO THE UNIT.

NO COMBUSTIBLE MATERIAL WITHIN 6" [152] OF THE TOP OF THE FIREPLACE.

NO COMBUSTIBLE MATERIAL WITHIN 1" [25] OF THE SIDES, BACK AND FRONT OF THE
FIREPLACE.

COMBUSTIBLE MATERIAL SHALL NOT BE PLACED DIRECTLY ON THE FACE OF THE
FIREPLACE, TOP AND SIDES.

STEEL SURFACE MAY BE COVERED WITH NON-COMBUSTIBLE FINISHING MATERIAL.

3" BLACK TRIM MAY BE COVERED WITH COMBUSTIBLE FINISHING MATERIAL.

1" CLEARANCE TO THE B-VENT MUST BE MAINTAINED.

Содержание 4-SS-2-GL






































Результаты поиска

Содержание 4-SS-2-GL

Отзывы:

Похожие инструкции для 4-SS-2-GL

Бренды по названию

Популярные бренды

Stellar Hearth 4-SS-2-GL, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 4-SS-2-GL

Отзывы:

Похожие инструкции для 4-SS-2-GL

Бренды по названию

Популярные бренды