- 10 -
- 11 -
GB
1� About this document
Please read carefully and keep in
a safe place�
– Under copyright. Reproduction
either in whole or in part only with
our consent.
– Subject to change in the interest
of technical progress.
Symbols
!
Hazard warning!
...
Reference to other informa-
tion in the document�
2� General safety precautions
• Only use genuine replacement parts.
• Repairs may only be made by
specialist workshops.
3� MotionSwitch LED Z-Wave
Proper use
– Infrared motion detector with orienta-
tion light and Z-Wave interface for
indoor power sockets.
Movement triggers lights, alarms and
many other devices. For your conven-
ience, safety and peace of mind. The
integrated pyroelectric infrared detector
senses the invisible heat radiated from
moving objects (people, animals,
etc.). The heat detected in this way is
converted electronically into a signal that
switches ON the interconnected load.
Heat is not detected through obstacles,
such as walls or panes of glass, and will
therefore not activate the light. The in-
frared sensor can be used for switching
light ON and OFF automatically. The unit
is not suitable for burglar alarm systems
as it is not tamperproof in the manner
prescribed for such systems.
The button activates and deactivates
the functions programmed via the Smart
Friends app. The orientation light can be
switched ON and OFF via the sensor
or the button on the MotionSwitch LED
Z-Wave. The relevant setting can be
programmed via the Smart Friends app.
This device can be integrated into the
Smart Friends system or any other
Z-Wave network. Z-Wave is a wireless
standard for interconnecting Z-Wave
devices. The power-socket sensor can
be used for wireless-based building
automation.
Besides certified Z-Wave controllers, it is
recommended to use the Smart Friends
box. This smart-home control centre
can be used for interconnecting Z-Wave
products from STEINEL and the Smart
Friends products from ABUS, Paulmann
and Schellenberg.
Package contents
(Fig� 3�1 )
Product dimensions
(Fig� 3�2 )
Product components
(Fig� 3�3 )
A
MotionSwitch LED
B
Button
C
Sensor
D
Orientation light
Sensor detection zone
( Fig� 3�4/3�5)
4� Mounting
• Check product for damage.
• Do not use the product if it is
damaged.
• Select an appropriate power
socket, taking the reach and motion
detection into consideration. The
most reliable way of detecting
movement is to fit the sensor so
that it points across the direction in
which people walk and by ensuring
that no obstacles obstruct the line
of sensor vision.
Mounting procedure
• Fit sensor into the power socket
so that it is aimed in the required
direction.
(Fig� 4�1-4�4 )
5� Function
Factory settings
Twilight level: 2000 lux
Time setting: 3 minutes
The motion detector will also work
without being integrated into a Z-Wave
network. In this case, the time setting
is permanently set to 3 minutes. In this
setting, the integrated LED light or a
directly connected Z-Wave actuator will
be activated.
After the 40-second calibration phase,
the motion detector is activated for
sensor mode. The motion detector
can now be integrated into the Z-Wave
network.
The settings can be made via Z-Wave
network.
Twilight setting
The twilight level can be infinitely varied
in the range from 2 to 2000 lux via the
Smart Friends app.
Note:
To adjust the detection zone in daylight,
the control dial must be set to 2000 lux
= daylight operation.
Time setting
The time setting can be adjusted in the
range from 5 seconds to 15 minutes via
the Smart Friends app.
6� Integration into Z-Wave
networks
This product can be operated in any
Z-Wave network with other Z-Wave
certified devices from other manufac-
turers. All non-battery operated nodes
within the network will act as repeaters
regardless of vendor to increase reliabil-
ity of the network.
Inclusion
Add
Exclusion
Remove
These instructions for including and
excluding STEINEL Z-Wave products
have been written for the Smart Friends
system. They may not always apply to
other Z-Wave products. You will find
further details in the description of your
Z-Wave controller. To start the motion
detector's inclusion or exclusion mode,
press the button three times in rapid
succession.
Following exclusion, all configuration
parameters (time, sensitivity etc.) re-
main intact until the next inclusion and
the power-socket sensor now works in
standalone mode.
Adding MotionSwitch LED to the
Smart Friends system:
1
Download Smart Friends app from
the app store.
GB
