Steinbach POOLRUNNER 00-61010, Руководство пользователя

Страница: 6 / 36

Poolrunner | 2013_V1 Page 6 of 36
EN
Description of control panel, Figure 5
Nr.
Name Specification Function
1 Pool Distance Pool distance Set the pool size
2 Run time Auto running time Set the running time
3 Stop Stop Stop
4 FWD/REW Manual for-
ward/backward
To move the clean-
er to a certain loca-
tion
5 Auto run Automatic working Cleaner starts run-
ning in automatic
program
6 Working time Display of the se-
lected working time
7 Pool width Display of the set
pool size
Function of jet propulsion, Figure 6
Each on the front and on the back of the cleaner there are two ad-
justable control nozzles for the drive in the water. The sucked foul
water is first cleaned through the filter bag and then used for the
drive for the cleaner above the thrusters. The nozzles are adjustable,
depending on the size and pool type, to achieve the best cleaning ef-
fect.
Recommended nozzle settings:

High speed / less cleaning (with low pollution) Figure 7,8,9,10

Slow speed / high cleaning efficiency (moderate to heavy contami-
nation) Figure 11,12,13
The above are recommending settings and operator can select a
proper nozzle direction based on above principle actual pool situa-
tion.
Commissioning
Since you have made your settings, you can put the cleaner careful-
ly and slowly into the pool. Please refer to the following pictures as
the cleaner may be best placed in the pool.
Figure 14,15,16
The cleaner must always be committed or removed to the pool that
the underside of the cleaner facing the pool wall, to avoid possible
scratches on the pool surface.
Figure 17,18
IMPORTANT! Figure 19,20
Care and Maintenance
Cleaning the filter bag
Unfold the retaining ring and open the cleaner. Figure 21,22
Press the buckle on the base of the cleaner and take off the filter
cartridge. Figure 23,24
Take off the filter bag, drain and clean it and put on the filter bag
again. Figure 25,26,27
Important
Please press the buckle to remove or restore the filter cartridge. If
this is not observed, it may cause damage to the lower part of the
cleaner.

Press the buckle simultaneously . Figure 28

Do not pick up the two parts of the cartridge at the same time . Fi-
gure 29

The installation must be initiated from one side . Figure 30

Press the buckle . Figure 31

Press the buckle on the other side . Figure 32

Lift out the filter cartridge from one side . Figure 33

Install the filter cartridge . Figure 34

Remove the filter cartridge . Figure 35
Remove bzs. Assembly of the filter bag . Figure 36
Tips and advices

Each time the cleaner is removed from the water, the filter element
has to be cleaned.

The pH-value of the pool water must be between 7.0 - 7.4.

The water temperature must be between 10 ° C and 32 ° C.

After pressing
the "power off" button, the “power on” button can’t
be pressed for 30 seconds.

We recommend to keep the cleaner between 5 ° C and 40 ° C in a
shaded, well-ventilated place. The supply cable must be wound up
for storage. (The float on the cable must not be moved, so that a
perfect swimming of the cable in the water is maintained) Avoid di-
rect exposure to the sun all the time!

Before using, please read the instruction for fault rectification thor-
oughly.

Keep the cleaner always on the handgrip to remove it in and out of
the pool.
Trouble Shooting
Symptom Possible reason Corrective action
Cable twists or
coils up.
The pool cleaner
turns while cleaning
the water (note, this
is normal)
.
Unplug power line,
complete the cable
and unscrew.
Obstruction in pool.
Remove obstruction in
pool.
The cable in the wa-
ter is too long.
Get the excess part of
the cable from the wa-
ter. The cable in the
water has to be long
enough to allow the
cleaner to reach all
corners of the bath.
The cleaner does
not reach all pool
area.
Connecting cable is
not long enough.
Allow the cleaner to
reach all corners of the
bathroom, enter the
maximum length of the
connecting cable into
the pool, but consider
a corresponding mini-
mum distance of the
control unit to the pool
.
The pool shape
doesn’t
make a
complete cleaning
possible .
Slide the pool cleaner
by hand to the places
where was not cleaned
and restart manually
backwards forwards
The water cycle of
the bath is switched
on
.
Turn off the filter
pump.
The cleaner does
not work.
Too much air in the
case. Turn off the machine
and let all the air es-
cape
.
A foreign object is
in/at drive. Contact the service
center.