background image

Maintenance

BA_Activa Lift 2 Elektro ©_D_10_2010

   36

www.steelcase-village.de

CAUTION

The desk may be damaged by the use of unauthorised spare parts!

 

Only components provided by Steelcase Werndl AG may be used as spare parts. 

The use of other parts requires the consent of Steelcase Werndl AG.

 

The specified maintenance and inspection intervals must be complied with.

Liability 
disclaimer

Steelcase Werndl AG shall assume no liability for and will provide no guarantee in the following 
cases (See 1.4 Liability disclaimer on page 5):

• Inadequate monitoring of the product components (functional checks)

• Improper maintenance

• Maintenance performed by third parties

• Maintenance performed by unqualified and unauthorised persons

• Use of components and adaptations not supplied by Steelcase Werndl AG

• Unapproved changes to the product with regard to its construction and implementation

• Deliberate misuse

• Improper use.

8.5    Cleaning and care

Motor 
controller

CAUTION

Humidity may damage the operator panel and the control system.

 

Keep the operator panel free of moisture and liquids.

 

Keep the controller free of moisture and liquids.

Prior to cleaning, the motor controller must be disconnected from the power supply.

Only clean the motor controller with a dry or slightly damp cloth.

Desk

CAUTION

Material damage is possible due to unsuitable care measures.

 

Only use polishing and cleaning agents that are suitable for the respective mate-
rials (fabrics, wood, plastics, metals).

For cleaning the surfaces of the desk off-the-shelf cleaning agents can be used.

Ensure that only care and cleaning agents are used that are suitable for the respective materials 
(wood, plastic, metal, etc.).

Содержание Activa Lift 2










































Отзывы: