ENGLISH
33
33
FILLING THE FUEL TANK
1. Choose an adequate area to refill the deposit.
2. Shake the recipient so that the petrol and oil mix
correctly.
3. Remove the petrol cap and refill with the mixture.
4. Close the petrol deposit and wipe off any excess
mixture that might have spilt with a dry cloth.
WARNINGS:
Stop the engine before refilling.
Do not start the machine in a closed area. The exhaust
fumes, the vapours of the petrol and the chain oil, all
contain carbon monoxide and other dangerous chemical
substances. In case of gas concentration due to insufficient
ventilation, eliminate from the work area everything that
impedes the correct flow of air and do not work in this area
again until it is well ventilated and the gas concentration
does not happen again.
Do not refill fuel in areas where flames, sparks or hot
sources are. Refill only in ventilated areas with engine off.
Do not overfill the fuel to try to overfill the fuel tank. In case
of petrol leakages, eliminate these before starting the
machine. do not attempt to start the engine but move the
machine away from the area of spillage and avoid creating
any source of ignition until petrol vapours have dissipated.
Stay away at least 3 meters from the zone where you
have refuelled before started the machine.
Refill fuel before to start the machine.
Do not remove the petrol cap whilst the engine is running
or engine is hot.
Do not use fuel with ethanol or methanol because will
damage the engine.
3.3 Ilustrated description
1. Back handle.
2. Safety lever.
3. Switch ON/OFF.
4. Fuel cap.
5. Starter handle.
6. Front handle.
7. Blade.
8. Muffler.
9. Choke.
10. Fuel tank.
11. Block handle lever.
12. Throttle trigger.
13. Gear Box.
14. Spark plug.
15. Primer.
16. Change in handle position.
17. Air Filter.
4. Operating instructions
4.1 Placement and testing
Use this machine only for jobs for which it has
been designed. The use of this machine for
any other jobs is dangerous and can cause
dangers to the users and/or to the machine.
Do not start the machine in a closed area.
The exhaust fumes and the vapours of the
petrol, all contain carbon monoxide and other
dangerous chemical substances. In case of gas
concentration due to insufficient ventilation, eliminate
from the work area everything that impedes the correct
flow of air and do not work in this area again until it is
well ventilated and the gas concentration
does not happen again.
Work only with good light. Do not use this machine at
night, with fog or with reduced visibility that does not allow
you to clearly see the working area.
Avoid operating the equipment in wet grass, where
feasible. Take special care when using this machine in the
rain or after rain because the ground is slippery and you
can slip.
If you lose your balance or fall, let go of the handle switch
immediately.
Do not use this machine if you are tired, sick, are taking
medicines, or if under the effect of alcohol or drugs.
Do not use this machine when you are tired or under
the influence of drugs, alcohol or medicines. A moment
of distraction when using this machine can cause severe
personal damage.
The lack of rest and fatigue can cause accidents and
damages.
Never cut above shoulder level.
Do not get near the cutting elements of the machine when
the machine is functioning.
Do not rely solely on the security elements of the machine.
It is important to check that all parts are well tightened. If
you detect any anomaly, stop the machine straight away
and check the machine carefully. In case of any damage,
take the machine to your nearest service agent. Never
carrying on working if the machine is not working correctly.
Remember to always use the machine with clean hands
and without petrol and oil.
Clean the work area and eliminate any obstacles that could
cause accidents. Check the work area and remove any
objects that could get entangled to the cutting elements.
Also remove any objects that could be expelled by the
machine or its parts when getting in contact with these.
Do not allow anybody to enter the working area.
