manualshive.com logo in svg

State Water Heaters 119300, Руководство по обслуживанию


Поделиться
Скачать
background image

18

Servicing should only be performed by a Qualified Service Technician

• 

Reinsert connector on Flame Sensor and make sure the electrical connection is clean and tight.

• 

Recycle unit again to start another ignition cycle. If the burner ignites but the flame sense rod still fails 

to detect flame, contact Commercial Technical Support.

BURNER DOES NOT IGNITE

Failure to ignite (no flame) usually means a gas supply or Gas Control Valve problem. If you do not see a 

brief blue flame through the sight glass during the ignition cycle (at the moment the Gas Control Valve icon 

appears on the display), follow these steps:

• 

Remove  and  reinsert  the  Gas  Control  Valve  electrical  connector.  Make  sure  the  electrical  connections 

(pins) are clean and that the connector fits tightly.

VENTURI

LOW GAS

PRESSURE SWITCH

SUPPLY GAS

CONNECTION

GAS CONTROL

VALVE

COMBUSTION

AIR INLET

24 VAC SOLENOID

& WIRE HARNESS

GAS CONTROL VALVE ASSEMBLY: SUF 60120 - 100250 MODELS

LOW GAS

PRESSURE

SWITCH

SUPPLY GAS

CONNECTION

24 VAC SOLENOID 

& WIRE HARNESS

GAS CONTROL VALVE ASSEMBLY: SUF 119300 - 119500 MODELS

Содержание 119300

























































Отзывы:

Нет отзывов

Похожие инструкции для 119300

YAMADA NDP-20 series Maintenance Manual preview
NDP-20 series
Бренд: YAMADA Страницы: 14
Calpeda VAL Operating Instructions Manual preview
VAL
Бренд: Calpeda Страницы: 32
RainSoft UF Series Owner'S Manual preview
UF Series
Бренд: RainSoft Страницы: 16
Zehnder Rittling SL Installation, Operation And Maintenance Manual preview
SL
Бренд: Zehnder Rittling Страницы: 20
DAB NOVA UP 180MA Instruction For Installation And Maintenance preview
NOVA UP 180MA
Бренд: DAB Страницы: 184
DAB NOVA UP 180MA Instruction For Installation And Maintenance preview
NOVA UP 180MA
Бренд: DAB Страницы: 184
Gardena 2000/2 Li-18 Operator'S Manual preview
2000/2 Li-18
Бренд: Gardena Страницы: 17
Gardena 4100 Silent Operator'S Manual preview
4100 Silent
Бренд: Gardena Страницы: 12
HOMCOM 820-250V80 Assembly & Instruction Manual preview
820-250V80
Бренд: HOMCOM Страницы: 3
Pentair Pool Products SHURflo 358 Installation And Operation Instructions preview
SHURflo 358
Бренд: Pentair Pool Products Страницы: 2
Graco Check-Mate 450 Manual preview
Check-Mate 450
Бренд: Graco Страницы: 48
Liberty Pumps LEH150-E Series Owner'S Manual preview
LEH150-E Series
Бренд: Liberty Pumps Страницы: 83
Circor Leslie F-1240LDW Installation, Operating And Maintenance Instructions preview
Leslie F-1240LDW
Бренд: Circor Страницы: 19
Pentair Fairbanks nijhuis 2800 Installation, Operation And Maintenance Manual preview
Fairbanks nijhuis 2800
Бренд: Pentair Страницы: 28
NEO TOOLS 90-065 Translation Of The Original Instructions preview
90-065
Бренд: NEO TOOLS Страницы: 43
Airtecnics SMART ECG 1000 A Installation, Operation And Maintenance Manual preview
SMART ECG 1000 A
Бренд: Airtecnics Страницы: 22
Culligan Medallist 8" Owner'S Manual preview
Medallist 8"
Бренд: Culligan Страницы: 58
EQUATION IFH04-90-N Legal And Safety Instructions preview
IFH04-90-N
Бренд: EQUATION Страницы: 34

Бренды по названию

Популярные бренды

Загрузить еще бренды