State Water Heaters 119300 Скачать руководство пользователя страница 37

Страница: 37 / 56

Servicing should only be performed by a Qualified Service Technician

Connect the ground wire from the power supply to the grounding lug inside the junction box. See

Junction Box Assembly Figure below and "Wiring Diagrams" on Page 52 & Page 53.

6. Replace junction box cover when connections are complete.

Note

: Do not apply power to the water heater before installation is complete and the water heater is filled

with water.

ENABLE/ DISABLE SWITCH

The Enable/Disable Switch is NOT an "on/off" switch and does not disconnect 120 volt power to the CCB and

other heater components. When in the "Disabled" position the switch removes electrical power from the Gas

Control Valve so that water heating is disabled. The display, CCB, and other electrical components will still

be energized and the display will read "Water Heating Disabled". The Enable/Disable Switch can be used to

disable operation and reset error codes. To operate the water heater, make sure the switch is set to "Enabled"

position. Turn power off at the source (circuit breaker) during installation and servicing.

POWER SUPPLY TEST

Proper grounding and polarity can be verified with an AC volt meter by taking three voltage readings at the

power supply wiring inside the water heater's 120 VAC junction box.

Check for AC voltage between:

Hot & Neutral - should be approximately 120 VAC.

Hot & Ground - should be approximately 120 VAC.

Neutral & Ground - should be approximately 0 VAC.

Heater Wiring

(Factory Installed)

Ground

Ground Terminal

Lead Wire

L1 (Black Wire)

Neutral (White Wire)

Junction Box Assembly

Enable/ Disable Switch

Содержание 119300

























































Результаты поиска

Содержание 119300

Отзывы:

Похожие инструкции для 119300

Бренды по названию

Популярные бренды

State Water Heaters 119300, Руководство по обслуживанию

Результаты поиска

Содержание 119300

Отзывы:

Похожие инструкции для 119300

Бренды по названию

Популярные бренды