State Water Heaters 119300 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 56

background image

31

Servicing should only be performed by a Qualified Service Technician

Results/Actions

•

If the ohm meter shows continuity (closed circuit) between the two outside pins (red wires) the ECO

switch has reset properly. If the Control System continues to lock out displaying

Energy Cut Out

(ECO)

on the UIM with continuity through the ECO present call the toll free support phone number

listed on the back cover of this manual for further assistance.

•

If the ohm meter shows no continuity (open circuit) between the two outside pins (red wires) and the

tank temperature is known to be at or below 100°F (38°C) - replace the Temperature Probe. Follow

the draining and filling instructions in the maintenance section of the Instruction Manual that came

with the water heater when replacing the Temperature Probe.

•

If the Control System continues to lock out displaying

Energy Cut Out (ECO)

on the UIM and the

water temperature inside the water heater is becoming excessive (at or above 201°F/94°C) check

water system piping; ensure heat is not being added by any other heating appliances or heat sources.

If all these tests have been performed and the Control System continues to lock out call the toll free

support phone number listed on the back cover of this manual for further assistance.

«
...
30
31
32
33
34
...
»

Содержание 119300

























































Отзывы:

Нет отзывов

Похожие инструкции для 119300

Бренд: Zibro Страницы: 16

Бренд: TapFlo Страницы: 35

Бренд: Rainman Страницы: 17

Бренд: Valor Fires Страницы: 17

Бренд: TapFlo Страницы: 63

Бренд: Daalderop Страницы: 16

Bell & Gossett Domestic 616PF

Бренд: Xylem Страницы: 4

Бренд: EAST OAK Страницы: 14

Бренд: Zibro Страницы: 12

Duro Titan SBA025T1

Бренд: Canature WaterGroup Страницы: 8

VERSAFILLER P EBF Series

Бренд: Oasis Страницы: 21

Бренд: Ingersoll-Rand Страницы: 12

Бренд: Parasol Страницы: 11

Бренд: DeLonghi Страницы: 7

Бренд: Easy@Home Страницы: 38

Бренд: Protemp Страницы: 51

Бренд: Jaga Страницы: 11

Appino BEATZZ black

Бренд: Vasner Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды