background image

PLIT620  REV. B     11/2/22 

Multi-Colored Quick Stick Arrow Board 

DLQSMC-ARO 

DLQSMC-ARO2 

1.  There is a slot along the length of the back of the 

arrowstick that should be used to facilitate mounting. 
Insert the heads of the two enclosed #10 carriage bolts 
into the hole in the slot.  

 

2.  Slide them along the channel to the desired location and 

mark the locations for your mounting holes on the 
mounting surface. 

 

3.  Drill your holes and mount the light using the enclosed 

washers and nuts. 

 
 
 
We also include two L-Brackets to facilitate mounting. 
These are optional and do not need to be used. 

Prior to mounting the light, determine 
the path your cable will take. The cable 
should exit the left side when you are 
facing the lights on the arrowstick 
mounted on the rear of the vehicle. 

Mounting Instructions 

-2- 

 

Electrical Connections 

Use standard On/Off switches rated for 5 amps and make your connections 
according to the wiring diagram below.  

Note:  The wires are shown above in order of Priority. Higher priority wires will override 

the patterns on any lower priority wires for the heads that are enabled. 

HIGHEST PRIORITY 

LOWEST PRIORITY 

Pink > White w/Brown > Green w/Yellow > Orange w/Red > Yellow 

Default Wiring Setup 

(Wire Setup 1)

 

This wiring diagram below applies to the default programming of this light. There are 
several additional advanced features that, if used, will affect the wire functions 
shown below. Most applications will not require this reprogramming, but you can 
find these options described in detail under the 

Advanced Programming

 section.

 

**Standby current < 0.001A 

  Left Arrow 
                              Both=Center-Out 
 Right Arrow 

10 AMP Fuse 

Ignition-Switched Relay 

12VDC BATTERY 

The RED wire must be connected to +12VDC 
for any of the functions to work. 

Function 

Wires 

Function 

Wires 

ORANGE w/RED

 - Color 1 Full Warn

 

 

 

WHITE w/BROWN

 - Left Arrow

 

 

(Color 1 - Head Groups 1-6)

 

GREEN w/YELLOW 

- Right Arrow

 

 

(Color 1 - Head Groups 3-8)

 

RED w/GREEN

 - Pattern Select 

BLACK

 - Ground 

YELLOW

 - Color 2 Full Warn

 

 

 

PINK

 - Steady Burn Tips

 

 

(Color 2 - Head Groups 1 & 8)

 

RED

 - Power 

6  6 

Head Groups 

Содержание DLQSMC-ARO






Отзывы: